Error 17 displayed on the screen

Is your oven in power save mode? Does oP-4 scroll across the display? The power save mode turns off the time of day clock display according to page 17 of the user manual. If power save is turned on to turn it off press the clock/options 4 times (if op-4 appears in the display then press clock/options 4 more times to turn off power save mode. Then you should be able to set the time of day clock by pressing clock/options ONCE enter the time and press start. Hope this helps.

Hi Tania,
Have you gone through this checking sequence.? it's from a Panasonic a/c manual. It could be something as simple as a clogged filter. Once you have rectified the fault, you will probably have to clear the fault code as described at bottom below, before it will condescend to work again.
David

• Once error occurred during operation, the unit will stop its operation, and Timer LED blinks.
• Although Timer LED goes off when power supply is turned off, if the unit is operated under a breakdown condition, the LED will ON again.
• In operation after breakdown repair, the Timer LED will not blink. The last error code (abnormality) will be stored
  in IC memory.

14.2.2 To Make a Diagnosis

1. 1 Timer LED starts to blink and the unit automatically stops the operation.
2. 2 Press the CHECK button on the remote control continuously for 5 seconds.
3. 3 "- -" will be displayed on the remote control display.
   Note: Display only for "- -" (No signal transmission, no receiving sound and no Power LED blinking)
4. 4 Press the TIMER ? or ? button on the remote control. The code "H00" (no abnormality) will be displayed and signal will be transmit to the main unit.
5. 5 Each press of the button (? or ?) will increase error code number and transmit error code signal to the main unit.
6. 6 When the latest abnormality code on the main unit and code
   transmitted from the remote control are matched, Power LED will
   light up for 30 seconds and a "beep" sound (continuously for 4
   seconds) will be heard. If no codes are matched, Power LED will light up for 0.5 seconds and no sound will be heard.
7. 7 The breakdown diagnosis mode will be canceled unless pressing the CHECK button continuously for 5 seconds or operating the unit for 30 seconds.
8. 8 The LED will be off if the unit is turned off or the RESET button on the main unit is pressed.

14.2.3 To Display Memorized Error Code (Protective Operation)

1. 1 Turn power on.
2. 2 Press the CHECK button on the remote control
3. 3 "- -" will be displayed on the remote control display. Note: Display only for "- -" (No signal transmission, no receiving sound and no Power LED blinking)
4. 4 Press the TIMER ? or ? button on the remote control. The code "H00" (no abnormality) will be displayed
   and signal will be transmit to the main unit.
5. 5 Each press of the button (? or ?) will increase error code number and transmit error code signal to the main
   unit.
6. 6 When the latest abnormality code on the main unit and code transmitted from the remote control are matched,
   Power LED will light up for 30 seconds and a "beep" sound (continuously for 4 seconds) will be heard. If no
   codes are matched, Power LED will light up for 0.5 seconds and no sound will be heard.
7. 7 The breakdown diagnosis mode will be canceled unless pressing the CHECK button continuously for 5
   seconds or operating the unit for 30 seconds.
8. 8 The same diagnosis can be repeated by turning power on again.

14.2.4 To Clear Memorized Error Code after Repair (Protective Operation)

1. 1 Turn power on (in standby condition).
2. 2 Press the AUTO button for 5 seconds (a "beep" sound is heard) on the main unit to operate the unit at Forced Cooling Operation Mode.
3. 3 Press the CHECK button on the remote control for about 1 second with a pointed object to transmit signal to
   main unit. A "beep" sound is heard, and the Error Code is cleared

1. Turn the computer off.
2. Turn the computer back on.
3. Immediately at the Dell logo screen, starting tapping the F12 key once a second until the One Time Boot menu appears (if the computer boots to Windows turn the computer off and try again).
4. At the One Time Boot menu, press the arrow key to highlight Diagnostics and press enter
5. Write down any Error Codes and Validation codes listed.

If computer does not start normally, use this checklist to identify specific symptoms and take the recommended corrective actions to resolve the problems.Perform a Hard Reset Do these actions first to clear all temporary setting before troubleshooting the problem.Disconnect all peripheral devices and remove all USB devices and media cards Disconnect the AC power adapter, remove the battery, and then press and hold the power button for at least 15 seconds to drain residual charge

1. Reconnect the AC power adapter (do not connect the battery), press the Power button and look for the LEDs to blink or glow, and listen for the sound of a disk drive and fan turning.

Perform each recommended corrective action and then attempt to restart the computer.Symptom 1: LED lights do not glow, display is black, no fan or drive sounds are heard, and computer does not startIf LEDs do not glow or blink when AC power adapter is attached and power button is pressed, there is no power available to the notebook.

• Check AC adapter wiring and power connection to the notebook.
• Connect a different AC power adapter and remove battery, then restart notebook.
• Connect a different battery and disconnect AC power adapter, then restart notebook.
• If there is no power available at the notebook, contact HP to purchase a replacement battery or AC adapter.

Symptom 2: LEDs blink or computer beeps but does not start Blinking LEDs or beep tones indicate a hardware failure during the pre-start up testing.

• Count number of blinking LEDs or beeping tones to help with diagnostics testing.
• Contact HP for technical assistance. There are no other user-initiated troubleshooting actions until error codes are resolved.

Symptom 3: LEDs glow, fan noise may be heard briefly, display remains black, and computer fails to startup or boot Usually occurs if a component is installed incorrectly, or there is a device conflict or failure.

• Connect an external monitor to check if the problem is the built-in LCD display or graphics card.
• Remove all CD/DVDs, SD cards, USB devices, peripherals and do a Hard Reset .
• If memory or hard drive components were replaced, reinstall original components.
• Remove memory modules and replace one-at-a-time.
• Remove and reseat hard drive.
• If possible, turn on power, press F10 to enter BIOS mode, and run Memory Test and Hard Drive Test .
• On newer notebooks, turn on power, press Esc to enter UEFI mode, and run Memory Test and Hard Drive Test .
• If possible, turn on power, press F8 to enter Windows Advanced Boot Options , and select Repair Computer option, or enter Safe Mode and run Memory Diagnostics .
• If all other methods fail , but computer can boot to BIOS, use recovery disk to recover the computer to original condition.
  Note: All programs and data are destroyed during recovery.

Symptom 4: Computer may display an error message on a black screen during startup or boot

• Search www.microsoft.com for terms in error message.
• Search www.hp.com for terms in error message.
• If possible, turn on power, press F10 to enter BIOS mode, do the corrective actions listed under Symptom 3 to run memory and hard drive tests.

Symptom 5: Computer displays a blue screen or continually re-starts After an error message is displayed, you can usually bypass the error and continue to run the notebook in Safe mode to install an updated BIOS or driver.

• Search www.microsoft.com for terms in error message.
• Search www.hp.com for terms in error message.
• If possible, turn on power, press F10 to enter BIOS mode, and run diagnostic Memory test and Hard Drive test .
• If possible, turn on power, press F8 to enter Windows Advanced Boot Options , and do one or more of the following:
  • Select Disable automatic restart on system failure to view error message.
  • Run Repair Your Computer .
  • Run Last Known Good Configuration .
  • Select Boot into Safe Mode and then select Run a Microsoft system restore .
  • Select Boot into Safe Mode and then select Uninstall recently installed programs .
  • Select Boot into Safe Mode and then run Windows Update .

Symptom 6: Computer displays the Windows logo screen and stops respondingIf no error message displays, turn on power, press F8 to enter Windows Advanced boot options ,and select Disable auto-restart to view error message.

• Search www.microsoft.com for terms in error message.
• Search www.hp.com for terms in error message.
• If possible, turn on power, press F10 to enter BIOS mode, and select Restore the BIOS defaults (F9) .
• If possible, turn on power, press F10 to enter BIOS mode, and run Hard Drive Test .
• If possible, turn on power, press F8 to enter Windows Advanced Boot Options , and select Last Known Good Configuration (Advanced) . .
• If possible, turn on power, press F8 to enter Windows Advanced Boot Options , and select Boot into Safe Mode and then Uninstall recently installed programs .

Update Computer After Resolving A Problem When the computer starts into Windows normally, you should install the latest updates and patches to prevent other start-up problems.

Instructions

1. When you press the Power button to start the boot process, the LED lights glow while the computer verifies that there is sufficient electrical power to activate the hardware.
   
   Effect & Solution: When you press the power button, the LED lights on the computer do not glow or the LEDs blink briefly and then stop. There is no sound of the fan or hard drive spinning, and the screen remains blank. The computer will not start if there is insufficient battery or AC adapter power.
   
2. The BIOS queries various hardware components used for the startup boot process.
   
   Effect & Solution: When you press the power button, the LEDs glow but there is no fan or hard drive sound. The LEDs may glow briefly and then go out.
   
   Or
   
   The LED lights blink, stop, and then blink a second or third time, but there is no sound from the computer and the screen remains blank. The sequence of the blinking lights indicates a specific error code.
   
   Or
   
   A series of beeping tones is heard. The sequence of beeping tones indicate a specific error code.
   
   If a hardware component has recently been replaced, or if the PC has been jarred or shaken, there may be a loose connection to the memory chips or hard drive which prevents the computer from starting.
   
3. The BIOS loads the basic input (keyboard) and output (advanced LEDs / display screen / boot drives) devices into memory.
   
   Effect & Solution: When you press the power button, the LEDs glow, the fan or hard drive sounds, are heard, but then the boot process stops and a black screen - with an error message - displays.
   
   The boot check has detected a communication error or conflict with a hardware component that must be corrected.
   
4. The BIOS loads the Windows operating system and starts the services that allow low-level control of all of the background operations.
   
   Effect & Solution: When you press the power button, the LEDs glow, the fan or hard drive sounds, are heard, the HP or Compaq Logo displays on a black screen, but then the boot process stops and a blue screen - with an error message - displays.
   
   The boot check has detected a hardware driver error or a software conflict that must be corrected.
   
5. Control is transferred to the Windows loader to initiate the display of the advanced settings in the Windows environment.
   
   The Windows logo displays during this step.
   
   Effect & Solution: When you press the power button, the computer performs all the steps in the boot process, but after the Windows Logo displays, the moving Windows progress bar or the rotating cursor stops moving and the boot process stops.
   
   An error message may display on a screen with the Windows logo. In some instances, there is no specific error message.
   
   Or
   
   A black screen appears and the computer attempts to restart.
   
   The Windows self-check has detected a software conflict that must be corrected.
   

did you try installing newest drivers from intel/gigabyte website? what you described looks to me as a overheating problem. try running the game with case open. are you running on the integrated GMA graphics or PCI-E graphics card(like geforce, radeon)?

it looks like the Inverter's gone in your screen, it works like a starter in a florescent tube, it 'kick starts' your screen to come on. Turning it on/off many times eventually 'kick starts' your screen and makes it come on eventually.

The clipping sound is the internal safety switch that keep shutting down the monitor.
It means there is an internal problem on the main board (overvoltage, bad component , short).
Try unplugging power cord and leaving it unplugged two or three hours, this will reset ICs by draining power completely from circuits, it is called hard reset, it rarely works.
CRT monitors waste up to 15 times more energy than TFT screen, if your CRT starts giving troubles, then it is a good time for upgrading it to a new TFT.
17'' start at $120


17'' Dell 1703FPt DVI LCD Monitor w/USB Hub (Black/Silver) -B

171ABB 17" Widescreen LCD Monitor - 1440x900 (WXGA+),

Envision H716A4 17 in. LCD Monitor

19'':
19'' Princeton VL1919 DVI LCD Monitor (Black)

19'' panoramic

V7 Series D19W12 19" Widescreen LCD Monitor

mi tv turns on but only in color blue,next tv turn off red light apear one time and second time flash twice,whit mi remote control power on tv turs on ,then whit mi remote control send change chanes or any other funcion the tv turns off,letme now if you solve yor problem ,and i apreciate if you have some tips for me,thank.

Your monitor has disco fever and will have to be shot in a midnight ritual in Palm Springs. Or, you will have to replace a diac circuit linking the display, power control, and power supply grounds (or possibly an overvolt protector of some sort in the power supply.) I don't know why for this kind of error the designer couldn't just put a message on the OSD in some random human language.