Speed drops when running on a set speed above 6.0, 7.0

Ask the manufacturer

Hi Jason:
Make and model might help but here's two ideas:
1) Remove muffler and clean it. They can get plugged up with carbon and the saw will run at low RPM but will quit because of excess back pressure when you try to rev it up.
2) Set the high and low speed carb settings. Start the saw then gradually increase engine speed until full throttle. Screw the hi-speed needle in slowly. If RPM immediately drops, back it out until Rpm increases, then starts to drop. Screw back in until peak rpm reached, then starts to drop. Back out to peak, then 1/3 turn more.
Set low speed so engine runs smoothly but chain does not turn.
Hope this helps.

drop flaps,
set AFR to tad rich, check power with brakes set
and then release brakes, taxi to full speed (above stall speed) and pull back the stick.
you are now took off and air born

To find the answer to what is wrong simply run the fault codes This you can do at auto zone for free Write in the comment box the codes and you will be advised as to what to do.

Around 25-35 at idle with a warm engine, 45-60 at cruise speeds.

sometimes if you open device manager and expand network adapters, then right-click on the wireless adapter and click properties, on the advanced tab, every manufacturer writes their drivers differently, but some have a setting that is something like compatibility and the choices are faster and more compatible (you have to choose one or the other). Only change one setting at a time, write down what you change, what it started at, and where you set it, then close the property window and test. If it makes it worse, set it back before trying another setting.

Obtain a copy of the Repair Part List for your model from Kitchenaid.com.
Download a Copy of the Kitchenaid Service manual.

http://www.kitchenaidparts.be/centers/servicemanual/mixer.pdf

You need to adjust the mixer speeds:

Remove the screw holding the End Cover and locate the three screws from the Control Plate.
All three (2 top left and right, and 1 bottom) must be adjusted.

1. Loosen the lock nuts enough & Turn the 2 top screws clockwise until they cannot be turned
anymore. Leave the bottom screw alone for now.
2. Use a dab of white paint or paper whiteout to mark the positions of the Phillips screws.
3. Plug in your mixer and Set the speed selector to "Stir".
4. Turn each top screw One full turn couterclockwise (alternating between Left and Right)
Keep making one full turn at the time (for both left and right) until the motor starts running.
5. Put your hand near the Agitator shaft and allow it to brush your finger slightly. Use your
watch or clock and start counting the number of times the shaft touches your finger in
60 seconds. The correct count should be 60 RPM (Rounds Per Minute). If it is less
or more than 60, give each screw 1/4 turn counterclockwise or clockwise and start counting
again. Now tighten both lock nuts.
6. Set the speed selector to "6" and turn the bottom screw either clockwise or counterclockwise
to achieve a speed of 180 RPM.

For your reference, the planetary RPM's for the 5-qt. tilt-head Artisan Stand Mixer are as follows:
Stir speed - 60
Speed 2 - 95
Speed 4 - 135
Speed 6 - 180
Speed 8 - 225
Speed 10 - 280

Hi,
This error is usually caused by an incorrect setting of either bus speed or multiplier (or sometimes processor chip operating voltage). These could be set either by software ie in BIOS or by changing tiny switches mounted on the motherboard.
Have you consulted your motherboard manual?
Try here: http://www.motherboards.org/files/manuals/1/p3v4x-102.pdf
or try the ASUS website and look under support or the discussion forums.
This will help: http://support.asus.com/cpusupport/cpusupport.aspx

These freq and voltage settings are set under BIOS which is usually accessed by hitting the DELETE key on your keyboard after turning on your computer.
Sometimes a quick fix is to enter BIOS as per the above instruction and selecting LOAD BIOS DEFAULTS or something similar to that and then save and exit BIOS and allow the computer to reboot.. That may get you to the point of booting up without the improper freq comb error.
If you have no luck playing with the above info, shut down your computer and remove the left hand side cover on your computer box or tower, so you can access the inner workings of your computer.
Remove the cooling fan from your processor chip. It will be a large square or circular (black or silver colour).
Take a look at your processor chip. Note the part number printed on the chip, which is only visible after you remove the cooling fan. For example it may say for example SL52P or something else. It may also be an AMD chip.
Search the internet for its specifications ie search for SL52P.
For example, if it was a Pentium 3 chip running at 800 Mhz go to google and search for specs of P3 800 Mhz processor with the part number SL52P.
Google returns the following info (based on the example above) of:
http://processorfinder.intel.com/details.aspx?sSpec=SL52P
ie its a chip that runs at 800Mhz speed with the memory running at 133 Mhz (800 mhz processor speed obtained by having the multiplier set to 6 but actually means the memory is running at 133 MHZ but the processor running at 6 times the speed of the memory bus ie 133x6=800 MHZ (one of the settings you need to get right in your BIOS settings)
So if you had this chip, in BIOS you would select 133 bus speed, with the multiplier of 6 usually locked down on the processor physical internal wiring.
If your BIOS doesnt allow you to play with the processor and memory bus settings (commonly done to make the processor overclock to a faster speed) the other option is that you have the DIP switches on your motherboard set to the wrong settings. Again, refer to to your motherboard manual. The DIP switches are tiny plastic switch blocks on the motherboard with a row of (usually) white sliding switches.

Intel chip info: http://www.intel.com/p/en_US/support?iid=hdr-AP+support

http://processorfinder.intel.com/List.aspx?ParentRadio=All&ProcFam=483&SearchKey=

Also Try this: http://processorfinder.intel.com/Default.aspx

Cheers,
Steve (Melbourne, Australia)

check the fuel filter ...or you high speed jets are clogged

Well, the blower resistor handles the lower speeds and the hi-blower relay handles the hi speed only. if the fan still works on the lower speeds then the resistor is bad. if the fan doesn't work at all then your motor has failed and or burn't the relay out also. if you can get your blower to start by hitting the kick panel above the pass. side foot area then the motor is bad. if you are handy enough to drop the kick panel and access the motor then check the connections at the motor. Then wack the motor and see if it comes on then. you will most likely find the problem if you follow those simple rules above. Good luck.