Question about Konica Minolta bizhub C250 All-In-One Laser Printer

1 Answer

Please install the image unit correctly and close all doors

The machine was complaining about the image unite ,then after changing it ,the machine start to show , please install the image unit correctly and close all doors on the printers screen so what do i do ?

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,175 Answers

Sometimes just open the doors and closing them a few times will work its sensing somethings open ,Make sure all is closed you may have too reinstall drivers. start over read all directions sometimes we get burnt out on trying to get something going give it a break for a bit then try again. could be a firewall or anti virus cause problems to.

Posted on Mar 03, 2016

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 44 Answers

SOURCE: installed the black imaging unit in konica bizhub

possible a bad image unit. you can try swapping the connector on the bottom of unit to see if it works.

Posted on Jun 28, 2010

  • 3 Answers

SOURCE: my bizhubb c250 is displaying

open front door then push the IU correctly then close the door and close the side door from your right side...

Posted on Nov 27, 2011

bendarden
  • 984 Answers

SOURCE: install imaging drum Bizhub c352

The best way to solve your problem is to download the official Konica troubleshooting solution manual. It will tell you how to pinpoint and fix every problem reported to Konica. CLICK HERE

Posted on Jun 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I resolve error code C-2451


Release new transfer belt unit
• A new installation is not detected when a new transfer cleaner unit (image transfer belt unit) is installed. Remedy 1 Reinstall unit. 2 Check there is a short circuit in the fuse of the transfer belt unit. 3 Check the PRCB connector for proper connection and correct as necessary. 4 Change PRCB

Feb 02, 2015 | Konica Minolta Bizhub C550

1 Answer

The machine reported problem with Fuser unit and all the four drums at once.


remove all consumables, turn off and leave off for 10 secs, turn on allow the machine to turn over at which point it will ask you to install the consumables, - install 1 at a time then close the doors , allow the machine tostep further and ask you again to install the next unit- this process will change when you get the faulty unit and try to insert, the machine will complain about all the consumables again- now you knowwhich part is faulty- replace -job done

Mar 12, 2014 | HP Office Equipment & Supplies

1 Answer

Hp laser jet 3500 printer has an error code 59,99 what can i do /


main motor has failed to reach revolution within specified time- in other words - something is siezed solid and is preventing the machine from turning over into normal warm up operation-
suggest if you have recently replaced a toner cartridge/ fuser/ Image transfer belt then remove the new item and cycle the power without the unit installed. if tour machine warms up then complains about no cartridge then you have confirmation of the new unit being faulty-
if you are using 3rd party toners/ fusers then that could also be your problem. 3rd Party toners do NOT save money rather they will incur repair costs as they are not correctly prepared for re-use.

Jan 16, 2014 | Office Equipment & Supplies

1 Answer

Please install the image unit correctly and close all doors


replace the cyan image unit with OEM unit

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Nov 15, 2013 | Konica Minolta bizhub C250 All-In-One...

2 Answers

There is an error code c-2558 showing on my machine konica minolta bizhub c452 please do let me know the proper remedy for it ASAP


Abnormally high toner density detected Black TRC sensor-

1. Correct the TRC Connection on the underside of the imaging unit if faulty
2. Reinstall black image unit
3. Change image unit
4. Change PWB-M
5. Change PWB-MFP

you can try # 2 then run 20-30 sky shops (copies with lid up to make black copies) put a white piece of paper over lead edge section of copy glass so you are only making 1/2 black copies if you don't the copy may jam in the fuser due to excess toner. after running copies turn machine off for 10 secs to reset and power backon. if problem continues I would change the image unit.

Aug 21, 2011 | Konica Minolta bizhub C250 All-In-One...

1 Answer

The imaging unit need to be changed but it was just changed


When a new Imaging Unit is installed there is a fuse contained within the new unit that blows and resets an electronic counter in the machine. If you installed or had installed a new imaging unit, then the only way the machine would be asking for a new imaging unit now is if either you ran about 70,000 copies or somehow the new unit did not reset the counter. I have never heard of one not resetting the counter as at the same time the counter is reset, the machine initializes the new unit and adjust the ATDC ratio. If this had not occured the mixture of toner to starter (developer) would not be correct and the copies would either become light (undertoned) or have a dark background (overtoned).
If you had the new unit installed then I would contact the service company that installed it and ask for a replacment. If you installed it yourself then there may not be much you can do. You can order a new reset fuse for around $5 and replace the fuse in your imaging unit so the machine thinks there has been another unit installed. precisionroller.com has them. Just go there and enter "Di350 fuse" in the search box. In case you were not aware, Your NEC is made by Minolta and is indenticle to a Di350/351.
Those would be your options.
Good Luck and Thank You for using Fixya.
WheatlandServices

Dec 17, 2010 | NEC IT3510 Copier

5 Answers

How do I clear error message C-2558 for the Konica Minolta bizhub C253


tis error means abnormal tonder density in the balck image unit take the blacke image unit out and shake it while holding it level and put it back in the machine to reset the error code leave the machine on and open then close the front door

Nov 12, 2009 | Konica Minolta bizhub C250 All-In-One...

3 Answers

Intermittent "Invalid Imaging Unit" messages


sounds like your printer engine is starting to take a long unhappy downturn..

Jun 16, 2008 | Samsung CLP-500 Laser Printer

1 Answer

Missing Imaging Unit


When I had this problem the solution was a tiny piece of paper which was jammed in the machine.
When the jam was cleared the message went away.
Hope this helps

Jan 29, 2007 | Minolta magicolor 3100 Laser Printer

Not finding what you are looking for?
Konica Minolta bizhub C250 All-In-One Laser Printer Logo

Related Topics:

534 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6850 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

George Mclaughlin

Level 2 Expert

364 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...