How do i setup the aux in a Jensen VM9410 car dvd player?
The back of the player there are RCA Jacks (red,white,yellow). I have an auxiliary cord thats connected already but when i play a song through my phone, everything works fine except the main singer is either low or distorted. I also have to raise the volume up just to hear the song... any suggestions?
Should wire HU's Power Const to Amp's Remote On. Instead you wired HU's Power Antenna to Amp's Remote On. So the stock amp got
triggered only in radio mode.
it probably got jammed in there what you can do is unplug the power source and replug it back in a brief power push should eject the disk. make sure you have your unlock codes as the unit may think it got stolen if you undo the power. if that does not work to get it fixed around $89 bucks Thanks and please rate
NORMALLY YOU ONLY HAVE TO CONNECT THE EARTH LEAD ( OFTEN PINK) TO THE HAND/PARKING BRAKE TOGROUND THIS TO ALLOW USE DVD ONLY WHEN CAR IS PARKED, WHEN NOT GROUNDED YOU WILL GET A BLUE SCREEN
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
These cable is to connect your tv to other hardware like a dvd player. Just plug the yellow cord on the yellow input in the TV and in the yellow output of the DVD, and the same thing for the other two colors.
The yellow it's for the image, and the white/red are for the stereo sound (right and left channels).
If you don't have extra hardware you wont need to connect that cable.
just connect the video(yellow) and audio(red&white) outputs from your dvd using a 3 wire RCA patch cord set to the AUX Video input on the back or side of your T.V.(also yellow red and white) then switch the T.V. to AUX input and play your dvd
Connect the composite video RCA (yellow) cable output of the DVD player to the TV's video input RCA (yellow jack). Connect the red and white RCA cable from the DVD players audio output to the TV's audio input (red and white jacks). Select the source input from the TV's control panel - if it has an input selector switch, set it to select the video source from the front panel input jacks if you connected the three cables - yellow, red and white on the front of the set. Or, change the channel to receive the video auxiliary input source instead of the broadcast station.
The DVD player has component video as well as the S-video and RCA video and two RCA audio outputs.
If your player is the same as my picture, the component video jacks are in a horizontal line at the top of the back of the player. The white and red audio jacks are in a vertical line to the left. The yellow video out jack is in the second line just below the component video jacks (in a line with the coax port, the S-video port is in between the coax and the RCA video out). (The white jack is at the top left of the connections block, red below that, and yellow to the right of the red.)
Sure. The wire u are looking 4 is located in the bottom right side of the plug. Under the Bat (Red) and Ground (Black). On the last hole on the harness. Had same problem. Hope this helps you.
first of all the rca jacks in the back of your radio are for plugging in an amp, not your mp3 player. there should be an auxiliary jack(looks like a headphones jack) in the front of the head unit. if there is no auxiliary jack in the front then you will have to go buy a new head unit with an auxiliary jack.
The yellow wires on back one has a white cap the other has a red cap those are the input wires you need to buy the cord that goes from a red and white RCA jack to a 3.5mm headphone jack
×