Question about Husqvarna Craftsman 36cc, 16 In. Gas Chain Saw

Open Question

Chain wont go back on saw

14 inch craftsman electric chainsaw

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
dontbother10

dontbother10

  • 2220 Answers

SOURCE: How interchangeable are replacement chain bars for

Your question can't be answered as aked.
If your saw requires an Intenz 14" Bar it's Oregon pns 140SDET041 or 140GPET041. Part number 140SDEA041 if not Intenz.
Plug in your requirements here:
Oregon Bar & Chain Selector
http://www.oregonchain.com/commonpgm/Selguide_Selctmfg.asp?BusId=OCS&SellReg=USA&LangId=ENG&ShowRem=Y&ShowAnsi=Y&ShowQuality=Y&ShowCombo=Y&usertype=OCC
Once you get a part number it can easily be converted to other manufacturers numbers. HTH
Lou

Posted on Nov 03, 2009

Ad

John Hermes

  • 135 Answers

SOURCE: while cutting the chainsaw bogs down and stops

Check the air filter and the muffler if either are plugged up it will not run smooth. Carb hi and low screws are very sensitive so if you change them, only move them a little at a time.

Posted on Jan 02, 2010

drallim

  • 4088 Answers

SOURCE: cant get the cover back on chainsaw

The chain brake should have been released before removing the cover. You will have to release it with a large flat-blade screwdriver in the connector that runs the brake from the control handle. Hope this helps!

Posted on Jun 04, 2010

Ralph

  • 130 Answers

SOURCE: Need to know the degree to set my electric chain

A 20" bar unfortunately does not narrow it down. Fortunately both the .325 pitch chain and the 3/8 pitch chain sharpen at 25 degrees and you should have one of these chains. Hope this helps.

Posted on Mar 02, 2011

Mark

  • 403 Answers

SOURCE: A Talon Black Hawk 14 electric chain saw AC

if the motor comes on, but no movement, then the clutch is smoked

Posted on Mar 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello, I have an old sears 14" electric chainsaw


There should be no adjustments ither than the correct tention, i dont mean to be rude, but you have put the chain back on in the correct direction, the sharp edge of the cutters on the top of the bar going away from the saw, on the bottom of the back coming back to the saw?

Jul 24, 2011 | Craftsman Garden

1 Answer

Need a manual for a 14" Craftsman electric chain


Use model number 315.34020 which is the same saw w/o power sharp. In fact the 34030 model is mentioned in this manual. I haven't found anything relating to the 34030 model specifically. Oregon products is able to cross reference the saw and find parts for it (less the power sharp feature.)

Jan 02, 2011 | Craftsman Garden

1 Answer

Poulan 14" electric, model# PLN1514


Hi there, a couple of features come to mind that may be the cause of your problem.

Firstly, make sure that the saw is unplugged from the power supply.
  • The chain brake is active and wont allow sprocket movement and hence the chain. If necessary, pull the front guard (in front of the front handle) back until it clicks.
  • Electric saws generally have an additional motor-stop feature built into the trigger mechanism which is deactivated when the trigger is squeezed. So, in order to move the chain along the bar the trigger needs to be squeezed releasing the motor-stop. A tip - wear gloves when handling chains and move the chain towards the bar tip ie in the direction of the cutters - if the chain suddenly stops you wont remove several layers of skin in the process ! better still use a screwdriver against the back of one of the cutters and move it forwards - there should be some resistance and there should be no slack chain on the underside of the bar. Hope this helps.

Nov 06, 2010 | Poulan 14" Chainsaw

1 Answer

How to put the chain back on a 14" Poulan electric chain saw


Remove the cover that cover the rear of the chain bar.Now,loosen the nuts that attach the bar and slide the bar reward.Now set the chain in the slotted part of the bar,pull it forward until there is abut 3/8 of an inch slack in the chain an tighten the nuts.Re-install the cover.

Sep 12, 2010 | Poulan 14 in. 2.0 Peak Horsepower Electric...

1 Answer

I bought a ryobi 14 inch electric chainsaw. Is


Use regular bar/chain oil available from home centers, hardware stores, and saw shops. Always keep the chain properly sharpened and tensioned so that you don't have to force the chain into the cut which causes motor overheating. If you need to make an 'under' cut, do so with the top of the bar--don't run the saw upside down. Good luck!

Jul 30, 2010 | Ryobi 18-inch Electric Chainsaw Chain Saws

1 Answer

Craftsman 16 inch cain saw sprocket wont turn


Sounds like the sprocket could be stripped. If so, then you would need to replace the sproket. I suggest you contact Master Parts at 800-466-1446 or online at www.masterparts.net. They may be able to help you.

Jun 09, 2009 | Remington Electric Chain Saw

1 Answer

Electric chain saw chain adjustment. How loose should it be?


the chain should not be sagging from bottom of bar.when you tighten the chain push the nose of saw up so that all of the slack is out of the chain.chain should snap back in the bar if you pull the chain up and let go.when i adjust a chain i push the saw forward to make the bar go up and stay there while i tighten the nuts.hope this helps, let me know

May 11, 2009 | Desa International Remington 14" Electric...

4 Answers

Wen electric chain saw -is it doa?


Are you pressing the trigger lock with your thumb before you pull the trigger? That's a safety feature to prevent accidental sawing.

There's not a sensor for the oil, but you don't want to run the saw dry. It takes a special bar/chain oil which is thicker than motor oil.

FYI... if you look for a manual on the web, search for "Wagner chainsaw" because Wagner bought the chainsaw business from Wen.

Mar 10, 2009 | Electric Chainsaw Sharpener

2 Answers

14 inch electric chain saw throws chain off


If a new chain ::
make and model is important here, as are guide bar length
a particular chainsaw, may be available with 12,14,16,18,20,22,24,26 inch guide bar,
likewise different saws (even from different makers) use the same size of chain
a chain for this saw may be sold in a variety of lengths or
may be sold in the longest length only and require links removed to suit smaller bars.
back to the store, with the saw, for confirmation

If an old chain::
stretched way beyond safety, replace

Sep 27, 2008 | Remington Electric Chain Saw

Not finding what you are looking for?
Husqvarna Craftsman 36cc, 16 In. Gas Chain Saw Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Garden Experts

J. Bradshaw

Level 2 Expert

121 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

dannydoesita

Level 3 Expert

770 Answers

Are you a Husqvarna Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...