How to connect spl700 amp to ez-m mini mixer 10x2 and 2speakers

YOU SHOULD SEE IF YOUR AMP HAS AN MAIN IN RCA INPUT IF IT HAS JUST PLUG THE OUTPUT OF YOUR MIXER THERE

Contact the manufacturer or try an on line search with Google for the manual. I do not know where you are so I cannot show you!
Try this link: https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=4&cad=rja&uact=8&ved=0CD4QFjAD&url=http%3A%2F%2Fwww.billebro.se%2Fproddoc%2FPRID_3602_doc_178.791_178.794_178.797_178.798_178.799_SPL_EQ_Stereo_Power_Amplifier.pdf&ei=d153VIToDozGsQS0lIKgDQ&usg=AFQjCNHGCnoz5TroiT7XlYDZ1MHyxFC0mg&bvm=bv.80642063,d.cGU

An external equalizer will not help this at all. The problem is likely within the amp (feeding the main speakers), the connections from the board to the amp, or the speakers themselves. In other words, the answer would be "NO." Best of luck!

What kind of output does the mini mixer have? If may not have enough to input your Carlsbro PA

The Mini KP generates Stereo output and you would run it to either a stereo channel on your mixer before the amp or into two channels of your mixer board and PAN them to opposite sides.

If you try to connect this to a monaural amp, like a guitar amp) your cable will ground out the output of this box. The minimum would be to builld a special resistive mixer to combine the channels before they go to your amp HOWEVER you will lose much of the effects without having a stereo system.

The order is mixer, equalizer and amp. The output of the mixer connects to the input of the equalizer and the output of the equalizer connects to the input of the amp. The equalizer has three types of input and output connections. They are XLR, 1/4 inch and screw terminals. The mixer will have one or two of the three. Choose XLR if possible on the mixer, choose line level output on the mixer if possible. A XLR male to female cable is needed for the connection. The equalizer has two channels, if the mixer has two output channels the two output channels of the mixer can connect directly to the two input channels of the equalizer. If the amp has two input channels, the two output channels of the equalizer can connect directly to the two input channels of the amp. If the mixer only has one output channel then only one channel of the equalizer can be used and one channel of the amp likewise. A XLR male to female connection cable can be used to connect the equalizer to the amp.

Try connecting the main output to the input of the Kaoss and the output of the Kaoss to your amp. You will get more signal.

Try running it in your FX loop ( out of the mixer into the Kaos, out of the kaos back into the mixxer or out of the mixer into the kaos and out of the kaos into your amp.

For dj use, industry standard would be something like a Pioneer DJM600 mixer. 4 channels w/ effects and a mic input. To use kaoss it's best to go into Send/Return input through the effects. By tapping on Send, all sound is sent out to the kaoss pad, and comes back into the mixer into the Return inputs. By doing this you can have the kaoss pad on sitting next to the mixer ready to apply effects all the time. Then connect the master outputs from mixer into your amp, or straight to powered speakers. Kaossilator is more of an instrument than effects unit, so plug in to channel 3 after your 2 cdjs in channel 1 and 2. You still have a spare channel left. I use 2 x 1200s and 2 x cdjs with kaoss pad through effects channel in this way. A 4 channel mixer is plenty.

perhaps its memory problem in your computer, caused by one of these:
- low RAM (use higher RAM)
- too much applications in start up (close unnecessary applications)
- too high quality setting in image mixer movie capture setting (set at normal or low quality)

or you could try to use option "EZ Video CD" for easy & quick VCD creation in image mixer, but it gives you lower movie quality