Mobility diagram I need a pic or diagram of how batteries are installed unfortunately the batteries were removed before I got involved .the case is also free floating but I suspect I can figure that out

Remove the battery pack from the chair and turn it over. Make sure you do this on a flat surface. I usually put a towel or rag under it. Turn it upside down. You will have to use a Phillips screwdriver to remove the 8 screws on the bottom. Once they are all loose you will have to turn the battery case back over. The 8 screws should fall out. This is the reason for the towel so they don't bounce or roll away. At this point you can lift off the top to remove the batteries. Each battery had a sensor taped to the side. You need to remember their placement and then remove. Then you can remove the connectors from the batteries. You just reverse this procedure to install the new batteries.

see pic below.



procedure:

1. Drain the cooling system.
2. Disconnect the negative battery cable.
3. To complete removal, refer to illustration.
4. To install, reverse removal procedure.
5. Install thermostat with jiggle valve or air bleeder at upper side.
6. Apply a continuous bead of liquid gasket to mating surface of water inlet.
7. After installation, fill the cooling system and run engine for a few minutes. Check for leaks.

Please see my tip at http://www.fixya.com/cars/r5929960-s_thermostat . These are genericinstructions. If you get stuck or need specific instructions for your car,please get back to me

At first install pc-suite into computer for that mobile. after installation you can transfer pictures from mobile to PC

This scooter requires (2) 12 volt 15 Ah batteries. Typically you would open the case and replace the two batteries inside not the entire case and batteries.
Locate the screws that hold the case together and open it. Make a diagram of the how the batteries are connected. Obtain the new batteries locally or on-line, install and fully charge.
Hope this helps.

1. Remove slide cover. Place calculator face down.
2. Using a small Phillips screwdriver, remove screws
from back case.
3. Remove back case.
4. Remove discharged batteries.
Caution: Avoid contact with other calculator
components while changing batteries.
5. Install new batteries positive side up, as shown on
diagram inside case.
6. Replace back case, and then replace screws.
7. Press OFF ON ON.
Caution: Dispose of old batteries properly. Do not
incinerate batteries or leave where a child can find
them.
Your calculator cannot hold data in memory when
batteries are removed or become discharged.

1. Remove slide cover. Place calculator face down.
2. Using a small Phillips screwdriver, remove screws from back case.
3. Remove back case.
4. Remove discharged batteries.
Caution: Avoid contact with other calculator components while changing batteries.
5. Install new batteries positive side up, as shown on diagram inside case.
6. Replace back case, and then replace screws.
7. Press: [OFF] [ON] [ON].
Caution: Dispose of old batteries properly. Do not incinerate batteries or leave where a child can find them.
Your calculator cannot hold data in memory when batteries are removed or become discharged.

To replace the batteries:

• Remove slide cover. Place calculator face down.
• Using a small Phillips screwdriver, remove screws from back case.
• Remove back case.
• Remove discharged batteries.
• Install new batteries positive side up, as shown on diagram inside case.
• Run a coin across the reset pad on the upper right hand corner of the printed circuit board.
• Replace back case, and then replace screws.
• Press [OFF], [ON/C], [ON/C].
Note: The calculator cannot hold data in memory when batteries are removed or become discharged.

Switch off the phone, remove the battery cover, take out the battery and look at the top part of the battery compartment, you'll see the sim slot there. Take a look here:

I am sorry that I can't show you better pic, but unfortunately, i got no nokia 2680 pic. But hope at least you'll be able to do it with the instructions given above.

If you need further help, let me know.


Good luck.

Thanks for using FixYa.

• Remove slide cover. Place calculator face down.
• Using a small Phillips screwdriver, remove screws from back case.
• Remove back case.
• Remove discharged batteries.
• Install new batteries positive side up, as shown on diagram inside case.
• Run a coin across the reset pad on the upper right hand corner of the printed circuit board.
• Replace back case, and then replace screws.
• Press [OFF], [ON/C], [ON/C].

The TI-30Xa uses two A-76 lithium batteries. Comparable battery model numbers include: Duracell® D357 and Eveready® 357

Remove slide cover. Place calculator face down. Using a small Phillips screwdriver, remove screws from back case. Remove back case. Remove discharged batteries. Caution: Avoid contact with other calculator
components while changing batteries. Install new batteries positive side up, as shown on diagram inside case. Replace back case, and then replace screws.