Question about Jet Tech Systems Dishwashers
If the machine will fill on its own when it is empty then the rinse cam on the timer is defective
Posted on Dec 29, 2013
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: Dishwasher keeps running
I have seen this several times, and all of the times it has a bad control board. usually if you take the control board out, you can see a visibly burnt spot on the back of it wher a connection has melted. Another possible slowrun time problem could be that the water coming into the dishwasher when it fills is not hot. If it isnt hot, it takes the dishwasher longer to heat the water to temp, and therfore it runs longer. Is the water coming out of your tap reasonably hot? if not you may need to turn up your water heater settings. But if nobody has messed with the water heater, or the tap where the dishwasher is attached and the problem just started then thats probably not it. Good Luck!
Posted on Nov 05, 2006
I just read this for the same problem: push sanitize, then heat and dry, sanitize, heat and dry, sanitize, heat and dry, cancel, then open and close the door. It worked. The dishwasher is running correctly even as I type this.
Posted on Mar 22, 2008
I had the same flashing light problem first the normal wash flashing light then the others. I tried shuting of the breakers but nothing. I tried resetting the panel by pushing normal wash and heated dry simultaneously and nothing. So I took the six screws holding the front panel out and unplugged the ribbon type wires and plug and unplugged it several times to help make a better contact and I was able to get it to work right away. This may not work for all but I worked for me. It is very easy to do and it's worth a try if you're having the same problem. It took me less then 10 minutes.
Posted on Sep 12, 2012
Tips for a great answer:
Oct 17, 2018 | Hobart Dishwashers
Oct 19, 2015 | Maytag MDB7809AWB - MaytagR JetcleanR Plus...
Apr 03, 2014 | Kenmore 24 in. 16052 Built-in Dishwasher
Jan 17, 2013 | Fisher and Paykel 23 in. DD-603 Built-in...
If clean light is blinking then it may be an
issue with heater circuit, door switch or wash pump, please reset the power to
the dishwasher. After, 5 minutes check if you are still getting the same error.
If yes, then it is a water heating fault. To resolve this error try pressing
this reset sequence-- Heat Dry - Normal - Heat Dry - Normal or High Temp - Air
Dry - High Temp - Air Dry or Hi Temp Scrub, energy saver dry, Hi Temp Scrub,
energy saver dry or High Temp Wash-Heated Dry-High Temp Wash-Heated Dry .
Now let the unit run for 2-3 minutes and then you press the Cancel/Drain button
and allow it to completely drain and reset. If this doesn't work then it's an
issue with the wash pump not pumping the water past the heater efficiently or
due to lack of water to heat. Please make sure that heater is not open
circuited and is heating the water efficiently. You'll have to check the heater
using a multimeter; the meter should read between 3000 to 3300 ohms (Use
multimeter on Rx1 ohm setting). If heater is fine then make sure water pressure
is optimum and fill valve is working fine. Hope this helps... Please post
back if you need more information.
Aug 30, 2011 | Whirlpool GU2400XTP Built-in Dishwasher
Oct 06, 2010 | Dishwashers
Aug 09, 2010 | Moyer Diebel 24 in. 501HT Built-in...
Jun 02, 2010 | Whirlpool 24 in. GU2500 XTP Built-in...
Feb 16, 2008 | Kenmore 15769 Built-in Dishwasher
Sep 10, 2007 | Fisher and Paykel 23 in. DD-603SS Built-in...
Oct 22, 2015 | Jet Tech Systems F-18DP - Dishwasher,...
121 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: