Telephone ring tone

Just look at the bottom of the phone, you will find ringer tone volume marked with low & high. Put it to low. For the manual, see the bottom-side of the phone to locate the model number & search the Siemens website for the manual.

sonunny

Do the buttons make a noise when your press them? If not then that part of the phone is broken.

The ringtone for the CO or outside line buttons can be programmed by pressing program then press the
CO button twice, enter the ringtone you want by dialing 01 to 08, press enter or store then program to end. This will set the ringtone for that line assuming it is programmed to ring at that phone. Transferred calls will use the ringtone of the intercom button which can be set by the same procedure. Use the same procedure if calls ring to a Group Directory Number(GDN) on the phone. The 7600 series of digital phones have ringtone settings of 01 through 30.

Press the function button once.Use the directional button to cycle through the options.Once you get to initial set or set rings option,press left or right to set the number the press the off button.If your option is initial set,press right,you have to scroll down to set answer machine options press right and set ring tones,I think up and down on directional pad.Good luck!

I'm going to take a chance here, because we don't have them. The au brochure says you have 8 tones, so try pressing Program, the button twice (be it intercom or a CO button), then dial 01-08 and STORE. By default, digital phones already ring 01 tone. You have to do this for each line and each phone to make it work.

Carl

Per the manual, If there is a musical note in the display with a slash thru it, you have turned off the ringer. You have done this by pressing and holding the # button.
If you have the manual it's on the bottom of page 20 and continues on 21.
If not follow these steps.

Press Menu
Press CID/PBK (Personal set)
Press Menu (Handset Tone)
Press Menu (Ring Tone)
Press Menu and then CID/PBK to select the volume you want
Press Menu (Save Setting)

click this link to get the manual

http://www.p4c.philips.com/files/c/cd4452b_37/cd4452b_37_dfu_aen.pdf

Receive Mode Settings Select from the following receive mode options to suit your needs. Once you've decided on which receive mode to use, follow the below instructions to set the receive mode using the operation panel. Receive Mode Setting

1. Press the <FAX> button to enter Fax mode.
   
2. Press <Menu>.
   
3. Press the right or left arrow button to select [Receive mode settings], then press the <OK> button.
   
4. Press the up or down arrow to select the receive mode that best suits your needs, then press <OK>.
   
   

Types of receive mode
Select the receive mode according to your needs.
Receive mode
Purpose
FAX/TEL AUTO SW When you want to receive faxes automatically as well as voice calls. FAX ONLY MODE When you want to receive only faxes automatically with your machine, or have a dedicated telephone line for FAX use only. DRPD When you have subscribed to a DRPD service with your telephone company. MANUAL MODE When you receive mainly voice calls and sometimes faxes, or want to receive faxes manually. ANS.MACHINE MODE When you want to receive voice messages on your answering machine and receive faxes automatically. FAX/TEL auto switch
FAX :
The machine does not ring but will receive the fax automatically. Voice call :
The phone attached to the machine will ring. Pick up the handset to answer the call. Note:

• Ring start timing and Telephone ring length can be specified in FAX/TEL auto switch in the Receive mode settings.
  
• If you want the telephone to ring when it receives a fax, connect a telephone to your machine and enable the Incoming ring settings in RX settings.
  
• The phone attached to the machine may not ring depending on the telephone type you are using.

FAX only
FAX * :
The telephone does not ring. The machine will receive the fax automatically. Voice call :
You will not be able to answer the call. * If you want the telephone to ring, connect the telephone to your machine and enable the Incoming ring settings in RX settings menu.


DRPD
FAX :
Your telephone line will ring according to the ring pattern you have chosen and receive the fax automatically. Voice call :
Your telephone line will ring according to the ring pattern you have chosen. Pick up the handset to answer the call. Note: Specify the FAX pattern in the DRPD: Set FAX ring pat. in RX settings menu.

Manual RX
FAX :
The telephone attached to the machine will ring. Pick up the handset and if you hear a beep tone, press the <Color> or <Black> button on the machine to receive the fax. Voice call :
The telephone attached to the machine will ring. Pick up the handset to answer the call. Note: If you are far from your machine, you can use the remote receiving function to receive faxes. Pick up the handset of the telephone connected to the machine and press 25 (the remote receiving ID).

Ans. machine connect
FAX :
First the answering machine connected to your machine will respond to an incoming call, and then the machine will receive faxes automatically. Voice call :
The answering machine connected to your machine will respond to an incoming call. Note:

• Set the answering machine to answer on the first or second ring.
  
• The entire message should be no longer than 15
  

when the phone rings just pick up the hand set and answer
if that doesn't work press the talk/answer button and answer

If this still exisits, I am a Vodavi tech. Give me a call