Power on,amber loight led on and no action

This is the only Reset procedure. It is a just a printer, not a computer or a phone ;>)

Please see below for resetting the printer:

1. Turn the printer on, if it is not already on.
2. Wait until the printer is idle and silent before you continue.
3. With the printer turned on, disconnect the power cord from the rear of the printer.
4. Unplug the power cord from the wall outlet.
5. Wait at least 60 seconds.

More items...
•
Feb. 16, 2018

Factory reset Officejet 6100 - HP Support Community - 6585824

There are some following steps follow to reset canon printer:

1.Turn off the printer.

2.Press and hold the Resume button (triangle inside a circle).

3.Whilst it is held down, hold down the Power button. The green led light should come on.

4.Keep the Power button held down. Release the Resume button and then press it twice. The light should go amber, then green again.

5.Release the Power button
.
6.Press the Resume button four times and then press the Power button straight after to confirm the selected action (Reset Counter Absorber).

7.Turn off the printer and then turn it on again

Hope that your problem solved

Hello Samaila,Would you please tell me the printer model,So i can help you,Regarding your fuser error...

Try using the Vista driver, it may work and may not have all the functions that was available under Vista.

Hi there.


Step 1: Manual Temporary
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

step 2 : Software for Permanant
1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3.Choose (SET DESTINATION 1) And it should be reset.
Sofware Download "After service mode Pls use software for permanent reset
Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Hi there it is ink error.
You can try to reset the cartages this may do it Please call back let us know if it worked for you, PLEASE.

1. Start with printer off
2. Press and hold resume Button (triangle in the circle) and click “Power” button. Green led should be on
3. While holding the Power button, release the Resume Button.
4. Without releasing the Power Button, click “Resume” button for two times and release Both Buttons.
5. Click “Resume” for four times then soon click “Power” button, to confirm the selected action (reset counter absorber).
6. Turn off the printer and turn on again

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Great you changed the toner cartridges but you may also need to do the following as well.

Imaging drum is low Light pattern Description The imaging-drum light is on. The printer continues to print without any action required until the imaging drum is empty. Action Order a new imaging drum. Have a good day

just check ur lcd display cable and try to clean and c it it will cme

Hi,

This looks like either there is an paper jam or carriage jam on the unit,

Check the rare access door weather there is a paper jam.

Remove the cartridges and try moving the carriage( the cartridge hold) left to right and right to left and check if its moving freely.

After these try disconnecting the power cable without turning off the unit and hold the On button for 15 secs and then plug in the power cable while your hold the on button.

This should probably fix the issue.

Please do let me know if there is still an issue.

be carful about putting you email up on posts, as bad people harvest them for spam, and much worse stuff. anyhow, make sure the cables are correctly and firmly plugged in and now go into start (xp) and into printers faxes, and their should be a printer icon, with the name: Hp 6110 printer. if there is delete it and restart your comp, once this is done reload the software that came with the printer on a cd. if you have lost the disk then you can get an all in one type driver off from here: http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?product=79477&lc=en&cc=us&dlc=en&lang=en&cc=us if the printer is still not happy, then go into the printer icon by right clicking it and look around until you see the port the printer is configured to, sometimes its the generic printer port set as active, but the printer is using a USB port etc... good luck.