At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Re: Display reads call pilot busy and I can not check...
This means that all extensions to the call pilot are in use or the call Pilot is locked up. Try again later or power cycle the Call Pilot if it is an external unit.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The "Error Rudder" message on the C600AD display could indicate an issue with the linear feedback unit (LFU) or the rudder angle sensor. The LFU measures the position of the rudder and sends that information to the autopilot control unit.
You may want to check the wiring and connections between the LFU and the autopilot control unit to ensure that there are no loose or damaged connections. If the wiring is intact, the LFU may need to be replaced or recalibrated.
You may also want to check the rudder angle sensor to ensure that it is functioning properly. If the rudder angle sensor is not providing accurate information to the LFU, it could cause the "Error Rudder" message.
It may be helpful to consult with a marine electronics technician or the manufacturer of the C600AD autopilot system for further troubleshooting and repair recommendations.
Sep 17, 2015 - Rosen Video DSHD0850P11 2009-2011 Honda Pilot In-Dash, 6.2? Display Multi-Media, Navigation System. 26 Mar 2013 Hightlights: * This Car Multimedia system fits Toyota Corolla 2007-2010. 2? Display ... Navigation. Virtual 6 disks CDC: V-6 disc changer memory (6 disc music can be memory in the.
A problem with answering this question is first that the main SYSTEM keeps this info not the handset, so for the 3x8, 6x16, and 8x24 systems you can do the following (PROVIDED, the installer did not change the passwords to access).
Press FEATURE * * 2 6 6 3 4 4 Enter Password: 2 6 6 3 4 4 Display will read: " A. Configuration" Press: NEXT Display will read: "B. General Admin"
(NEXT is always the button on the right of your lines/extension list, 2nd button down from top.)
4. Press: SHOW Display will read: "1. Sys speed dial" (SHOW is one key up from NEXT) 5. Press: NEXT Display will read: "2. Names" 6. Press the SHOW Display will read: "Set names" 7. Press: SHOW Display will read: "Show set:__" 8. Enter the extension number of which you wish to change the name Display will read: "<##:name>" 9. Press the CHANGE softkey 10. Using the dial pad spell out the name Ex: If you need the letter K press the 5 key twice and then press # to confirm the letter. Continue until the entire first name is spelled. (note: you are limited to 7 characters) 11. Press: NEXT (if you fail to do this step, the name will not be saved!!!) 12. Press the RLS key
I may be mistaken however I think you have to be on a model M7310, T7316, or M7324 phone (there should be at least one usually at the main desk) in order to program I don't think you can directly do it from the T7208.
If the FWD/DND light is lit solid, the extension is in DND if it's programmed properly. You can test this by pressing the FWD button and reading the display. It will clear and press it again and it will set and tell you what it did. (if DND and FWD are both set it shows 3 states).
At the phone, press intercom and dial *710x where x=2 for all calls, 3 for busy, 4 for no answer or 5 for busy/no answer plus the extension of the voice mail plus #. Your FWD light should blink and you have now set FWD to voice mail.
When high is displayed it means that the probe and controller is reading that your oil temp is 30 degrees over your set temp. Use an external probe, locate it about one inch above your probe in the tank check actual temp and compare to your set temp. If you find that it is not 30 degrees over than there may be a problem with your probe, wiring or the digital controller. With a multi meter you can check your probe resitance it should be at 942 ohms at 350 degrees.
Fax display screen always reads, "Auto receive". When attempting to
fax, the busy light flashes. Busy light stops flashing for 30 seconds,
then starts flashing again. Above is the default settings for the fax.
NGB0 indicates signal error or line condition error. U need to check the phone line. U can hook any single line phone to the phone line, check for tones without background noise.
The Call Forward is set up by using the BLUE Super KEY located below the display. You have to know the Voicemail Pilot Number to be able to complete the programming. Basically you press " superkey ", say NO to the prompts until Call Forwarding comes up, say YES to Call Fordward, choise the type of forward you want ( always, no answer, busy, busy/no answer )dial in the voicemail pilot number, press save and then press the superkey to exit programming. Good Luck
You can change the view for your Deleted Items by not showing how many items are unread. Right-click the Deleted Items icon, and you will be presented on how the messages are displayed - whether or not unread messages will be indicated.
×