I have lost instructions for dremel flex shaft attachment sue

Question 1

0helpful

1answer

How do you assemble a dremel flex shaft 225-01

You screw off the collar on the tool, remove the chuck and inner part. The chuck is replaced with a special chuck (no inner piece). The special chuck has a square opening in it's nose that accepts the square end of the flex shaft inner cable. Is is actually a speedometer drive cable, from yesteryear.
Then you pull the inner cable out slightly, if it will, and put the inner cable into the square opening of the special chuck on your dremel motor. once engauged, you carefully screw the outer shaft housing on to the end of your dremel motor.
What you want to avoid is damaging this area during flex shaft assembly. I have had success with turning the output side of the flex shaft, while tightening the outer flex shaft onto the dremel motor. Stop tightening if it starts binding...
Rotation seems to help with alignment of all parts.

Cheers,

Doc

Sep 30, 2019 • Dremel Tools & Hardware - Others

0helpful

1answer

Replacing the spring in the Flex shaft attachment for Dremel Model 225

Use a piece of wire with a right angle hook on the end Push the wire down until it is inside the spring lever sideways and pull out.

Jan 22, 2013 • Dremel 225 Flex - Shaft

0helpful

1answer

Flex shaft attachment won't work

find the little square attachment and place on the end of the dremel tool. I didid the same thing. Worked fine after I put the other part on.

Nov 06, 2012 • Dremel Variable - Speed Multipro Rotary...

0helpful

1answer

One end of the 225 t2 is a large receptacle with threads inside and a shaft below the threads.I have no adapter to connect it to the Dremel. The FlexiShaft came with the variable-speed Dremel but no...

To use the flex shaft, you need to remove the bit collet. Included in the kit is a nut looking item--mine is silver. It has a square end and screws on to the end of the dremel. It is simlar to the collet, but is slightly smaller. Then you place the square end of the flex shaft into the nut and screw the shaft on to the dremel.
Hope that helps

Jan 18, 2011 • Dremel 225 Multipro Flex - Shaft...

0helpful

1answer

How do I attach the flex shaft. Given to me by someone who hasn't used in a while and I just purchased a Dremel rotary. She did not have a manual with it.

You remove the bit you were using and connect using existing collet, just tighten and go.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/matt_8dbc24bf722649ac

Nov 04, 2010 • Dremel 225 Multipro Flex - Shaft...

2helpful

1answer

Need a replacement flexible shaft attachment . when i took flexible shaft off a piece appr. 2" long pulled out of shaft

The part you need is available at most Lowes and Home Depot stores. You can also order it online directly from Dremel. Ckeck your manual for the part number.

Mar 05, 2010 • Dremel 400 Xpr Rotary Tool

2helpful

1answer

Flex shaft attachment

Takes an adapter to screw onto the nose of the Dremel. The shaft itself is gripped by the correct size collet tightened as you would any bit.

Mar 02, 2010 • Dremel 225 Multipro Flex - Shaft...

32helpful

3answers

My Dremel tool motor still works but shaft won't turn?

Here's the email from I got from Dremel (in my case the flex coupling broke):
Inside the tool is a flex coupling and spline driver.

The flex coupling is # 2615294309 and the price is $ 1.25.
This is the hollow plastic sleeve about 1" long with grooves on the
inside, that goes between the motor shaft and the output shaft.

The spline driver is # 2615294308 at $ 1.00.
Spline driver sits on the direct end of the motor shaft. The flex
coupling sits over the spline driver. Spline driver is about 1/4",
hard plastic with grooves on the outside.

Total shipping for orders under $ 5.00 is $ 2.50. Orders over $
5.00 is $ 4.00.

I have provided ordering instructions below.

To order by phone: 1-800-437-3635, Monday-Friday from 7 am to 6 pm
central time. VISA, MasterCard or Discover is accepted.

To order by mail:
Dremel
4915 21st Street
Racine WI 53406

Dec 06, 2009 • Dremel Variable - Speed Multipro Rotary...

0helpful

1answer

Dremel Flex shaft attachment model 225

Dremel has an exchange program for the 225 Flex Shaft. Send your flex shaft and 17.90 and they will exchange it for you. Send it to DREMEL 4631 E. Sunny Dunes Rd. Palm Springs, CA 92264 Their phone number is 1-800-275-2052. Hope this helps. Dave

Nov 09, 2008 • Dremel Variable - Speed Multipro Rotary...

0helpful

1answer

Using the flex shaft attachement.

I dont think it should get that hot. Dremel has a program for the 225 Flex Shaft and for 17.90 they will exchange it for you. Send it to DREMEL 4631 E. Sunny Dunes Rd. Palm Springs, CA 92264. Their phone number is 1-800-275-2052. Hope this helps. Dave

Nov 02, 2008 • Dremel Variable - Speed Multipro Rotary...

Question 2

Anonymous

Master 2,176 Answers
Posted on Apr 18, 2009

Anonymous

Master

Joined: Oct 26, 2007

Answers

2176

Questions

6

Helped

1311856

Points

5445

There are no manuals I have found but I have a website and phone number for them the site is Dremel.com and the toll free number is 1-800-437-3635 you can use either one to get the manual you need.

Anonymous Dec 10, 2012

Okay, today is December 10,2012 and I just read this post. I was thinking to myself, "yeah right, what are the odds I'll find out information about this tool my wife got 12 years ago from an 800 number today?". Was I wrong ! I called and went through the normal telephone prompts all the while thinking this would be a waste of time. Wrong again. Thelady anwered, solved my probelm over the phone and will be sending me a manual. What a nice start to my day. Thanks for helping. Bruce McCall

×

Related Topics:

Trustworthy Expert Solutions

I have lost instructions for dremel flex shaft attachment sue

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

How do you assemble a dremel flex shaft 225-01

Replacing the spring in the Flex shaft attachment for Dremel Model 225

Flex shaft attachment won't work

One end of the 225 t2 is a large receptacle with threads inside and a shaft below the threads.I have no adapter to connect it to the Dremel. The FlexiShaft came with the variable-speed Dremel but no...

How do I attach the flex shaft. Given to me by someone who hasn't used in a while and I just purchased a Dremel rotary. She did not have a manual with it.

Need a replacement flexible shaft attachment . when i took flexible shaft off a piece appr. 2" long pulled out of shaft

Flex shaft attachment

My Dremel tool motor still works but shaft won't turn?

Dremel Flex shaft attachment model 225

Using the flex shaft attachement.

Not finding what you are looking for?

225 Multipro Flex - Shaft Attachment

How do you assemble a dremel flex shaft 225-01

Ask a Question

Top Dremel Tools & Hardware - Others Experts

Brad Brown

john h

ADMIN Andrew

Are you a Dremel Tool and Hardware - Other Expert? Answer questions, earn points and help others

Manuals & User Guides

Related Topics:

Trustworthy Expert Solutions

I have lost instructions for dremel flex shaft attachment sue

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

How do you assemble a dremel flex shaft 225-01

Replacing the spring in the Flex shaft attachment for Dremel Model 225

Flex shaft attachment won't work

One end of the 225 t2 is a large receptacle with threads inside and a shaft below the threads.I have no adapter to connect it to the Dremel. The FlexiShaft came with the variable-speed Dremel but no...

How do I attach the flex shaft. Given to me by someone who hasn't used in a while and I just purchased a Dremel rotary. She did not have a manual with it.

Need a replacement flexible shaft attachment . when i took flexible shaft off a piece appr. 2" long pulled out of shaft

Flex shaft attachment

My Dremel tool motor still works but shaft won't turn?

Dremel Flex shaft attachment model 225

Using the flex shaft attachement.

Not finding what you are looking for?

225 Multipro Flex - Shaft Attachment

How do you assemble a dremel flex shaft 225-01

Related Topics

Ask a Question

Popular Questions

Dremel 395 won't turn on

My Dremel lock nut won't budge. My collet is

Dremel 4200 stopped working

Dremel shaft lock spinning

My Dremel tool motor still works but shaft won't turn?

Top Dremel Tools & Hardware - Others Experts

Brad Brown

john h

ADMIN Andrew

Are you a Dremel Tool and Hardware - Other Expert? Answer questions, earn points and help others

Manuals & User Guides