Question about Precor Exercise & Fitness

1 Answer

Precor 9.35 won't stay on.

Treadmill console will come on for about 15 seconds. If I don't hurry up and press the password and start it will shut off and won't come back on. I have to wait for about 30 mins to try it again. If I do get the password in and start it ill be fine for about 4 mins and then shuts off. The switch is flipped the I can't turn it back on with the display working. The motor fan is running. There is a solid red led light on but goes off when the display goes off. Help!

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Precor Master
  • 12,223 Answers

You must replace the control board electronic.

Go to www.treadmilldoctor.coPrecor 9.35 won't stay on.  - a5bb443a-9b01-48c9-9230-29270afbdc24.gifm

and get it see the diagram how the control board control almost the 80% of the machine.

God bless you

Posted on Sep 18, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: I have a proform j8li treadmill, all 4 led lights

I have the exact same problem with the very same treadmill that i bouth 10 years ago and it has been sitting for 5 years unused. The last time it was turned on it worked but now that I plug it in and try to start it, everything works but the belt drive motor. Any ideas?

Posted on Feb 09, 2010

maxtreadmill
  • 832 Answers

SOURCE: Treadmill powers off when pressing Incline Increase "br 1" error

You may have a beltand deck problem. Test by the following procedure:
without the poweron stand on the walking belt, push the belt in the, direction it normally turns. If the belt is very difficult to turn (on most treadmill this means that you have high belt/deck friction I first apply silicone lubricant between the belt & deck to see if that clears up the problem. Most problems originate from the belt and deck 75 to 85% of the time

Posted on Jun 13, 2010

  • 1 Answer

SOURCE: Fuel FT94 Treadmill troubleshooting

It stops and when I unplug it it starts again this happens 4 or 5 times what is wrong?

sig@siglane.com

Posted on Nov 02, 2010

vetteman3002
  • 2299 Answers

SOURCE: I have a PROFORM J6

This is not a fuse problem. If it was a fuse then it would not work after it quit. It is the motor that is going out. The motor has a thermal overload. This is what is making the motor shut down. But it is not always the motor that is going bad. Sometimes you can oil the bearings and this will fix the motor from overheating. By the bearings I mean the ones in the front and rear roller of the treadmill.

Posted on Nov 30, 2010

  • 1 Answer

SOURCE: I have a Lifefitness Treadmill model TR 9100,

Ive just had lifefitness out to diagnose the same problem, its the Console PCB £413.74 all in from them to fit yourself Cant do anything else, save yourself the callout I was charged Good luck Adrian Webb 07780 993877

Posted on Jan 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change password on precore 9.35 treadmill?


Hello!

According to the manual (included in the link), there is no way to change the password on the Precore 9.35 Treadmill from its default setting.

If you would like to disable the password, follow these steps:
1. At the Precor banner screen, press STOP, SPEED?, SPEED?, ENTER, PROGRAMS very quickly
2. At the SELECT UNITS screen, press ENTER
3. Using the arrow keys, select DISABLED at the PASSWORD prompt
4. Press ENTER to accept these settings

https://www.precor.com/sites/precor.com/files/manuals/48854-103%2520933i_9.35i%2520Lit%2520Kit_1005_EN.pdf

Sep 18, 2017 | Exercise & Fitness

1 Answer

Horizon manual


once lubrication is complete, reset the console by pressing and holding STOP and SPEED + buttons for 5
seconds

Aug 02, 2014 | Precor Treadmill Belt/Deck/Lube Kit,...

1 Answer

Error 27


Precor Error 27, Too Much Drive Motor Current Probable Cause 1. The running belt and/or deck are badly worn.
2. Drive motor is shorted or de-magnetized causing a high power demand.
Corrective Action
  1. Check the amp draw using a clamp on AC volt-amp meter during loaded and no load conditions and compare values to a similar treadmill that is known to have a good running belt and deck. Replace the belt and/or deck if necessary. Don't forget, some units have a double sided deck which means it may be flipped over rather than replaced if it has an unused side.
  2. Test unit with a known good drive motor. Replace drive motor if necessary.
Precor Error Code 27

Feb 18, 2014 | Precor 933 Premium Series Treadmill

1 Answer

Can you advise please


reset the machine make this: God bless you
Unplug the treadmill. Locate the console key and place the safety or reset key into the treadmill console. Replace any parts that need replacing, or is large enough to trigger with a pencil eraser or Q-tip. Plug the treadmill plug back into the wall. Use the Q-tip to press the reset button. It may be necessary to hold the reset button down for a few seconds. "CL11" will appear in the display of the treadmill.

    • 3
Press the reset button one more time with the Q-tip. "CL21" should appear on the screen. Press the enter key. The display will change again and show "CL22." Keep pressing the enter key until the numbers cycle through to the number "CL26." Press enter one more time. The letter E should appear on the display screen.
    • 4
Press enter twice more. The letters "SS" should appear on the screen. When this happens, press the start/stop key. Making sure to keep well away from the tread, press enter to start the treadmill. The treadmill will start on its own. The treadmill will stop on its own after a few seconds. When it stops, press the power key two times. Remove the safety key and put in a safe place. Your treadmill is reset.move on to the next step.
    • 2
Locate the reset switch on the underside of the treadmill console. Usually the button

Nov 28, 2013 | Precor 935 Premium Series Treadmill

1 Answer

My precore 9.43 starts to run then in 5 seconds turns itself off. Says ERROR- nothing more.


proceed according and fix it. God bless you

1 )Locate the reset switch on the underside of the treadmill console. Usually the button is large enough to trigger with a pencil eraser or Q-tip. Plug the treadmill plug back into the wall. Use the Q-tip to press the reset button. It may be necessary to hold the reset button down for a few seconds. "CL11" will appear in the display of the treadmill.



  • 2

Press the reset button one more time with the Q-tip. "CL21" should appear on the screen. Press the enter key. The display will change again and show "CL22." Keep pressing the enter key until the numbers cycle through to the number "CL26." Press enter one more time. The letter E should appear on the display screen.

Jan 25, 2013 | Precor 9.4 Treadmill Motherboard Motor...

1 Answer

How to unlock safety code for precor 9.35 treadmill


Procedure 2.3 - Accessing the User Parameter Program
This procedure allows you to
change the following settings:

• Set Measurement Units
• Enable/Disable Password
• Set User Name

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.
2. Press keys STOP,5,6,7,1 sequentially.
3. The display will momentarily read SELECT UNITS
4. The currently selected measurement unit will then be displayed.
5. Use the UP, DOWN arrow keys to toggle between U.S. STANDARD and METRIC.
6. Press the ENTER key to select the currently displayed measurement unit.
7. The display will momentarily read, PASSWORD
8. Use the UP, DOWN arrow keys to select either PASSWORD ENABLED or PASSWORD DISABLED
9. Press the STOP or ENTER key to exit the program.

Sep 27, 2012 | Precor 9.35 Premium Series Treadmill

1 Answer

Password reset


Procedure 2.3 - Accessing the User Parameter Program
This procedure allows you to change the following settings:

• Set Measurement Units
• Enable/Disable Password
• Set User Name

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.
2. Press keys STOP,5,6,7,1 sequentially.
3. The display will momentarily read SELECT UNITS
4. The currently selected measurement unit will then be displayed.
5. Use the UP, DOWN arrow keys to toggle between U.S. STANDARD and METRIC.
6. Press the ENTER key to select the currently displayed measurement unit.
7. The display will momentarily read, PASSWORD
8. Use the UP, DOWN arrow keys to select either PASSWORD ENABLED or PASSWORD DISABLED
9. Press the STOP or ENTER key to exit the program.

Aug 24, 2012 | Precor 9.31 Treadmill

1 Answer

I have a precor 9.3 treadmill that works until you i start running on it, what is the cause?


1= LUBE the deck belt , this happen because enough friction produce shut down, for to protect the electronic system.
2= LUBE the rollers bearings too
3= measure the input voltage motor, if there are the motor need repair
4= measure the output voltage board, for input voltage motor, if there are NOT the board is faulty.
see the block
God bless you

7_20_2012_9_38_04_am.gif

Jul 19, 2012 | Precor 933 Premium Series Treadmill

1 Answer

What is the password the get the precor 3.1 treadmill to work?


Procedure 2.3 - Accessing the User Parameter Program

This procedure allows you to change the following settings:

• Set Measurement Units
• Enable/Disable Password
• Set User Name

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.
2. Press keys STOP,5,6,7,1 sequentially.
3. The display will momentarily read SELECT UNITS
4. The currently selected measurement unit will then be displayed.
5. Use the UP, DOWN arrow keys to toggle between U.S. STANDARD and METRIC.
6. Press the ENTER key to select the currently displayed measurement unit.
7. The display will momentarily read, PASSWORD
8. Use the UP, DOWN arrow keys to select either PASSWORD ENABLED or PASSWORD DISABLED
9. Press the STOP or ENTER key to exit the program.

Jan 27, 2012 | Precor 9.31 Treadmill

1 Answer

Precor 9.25i Treamill scrolls message "button is pressed"


Press Enter,speed up and speed down simultaneously. Then enter to view error buffer . press quick start/pacer-stop simultaneously to reset error buffer log. Hope this helps

Apr 06, 2010 | Precor 9.21 Treadmill

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Precor Exercise & Fitness Experts

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

135 Answers

Tom Chichester

Level 3 Expert

53071 Answers

Rick Hickerson
Rick Hickerson

Level 2 Expert

119 Answers

Are you a Precor Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...