How to set adh2129 - Adidas ADH2124 Watch

go to this link below
http://www.adidas.com/campaigns/watches_fw07/content/index.asphttp://www.adidas.com/campaigns/watches_fw07/content/index.asp

go to the link below for instructions
http://www.adidas.com/campaigns/watches_fw07/content/index.asp

In time mode, hold set (bottom right button) to change date and time. The selected (flashing) item can be changed in one direction only using the up (top right) button. Press set again to cycle through each item until desired settings are chosen.
In stop watch mode, the up button starts and stops the stopwatch, the set button will take a split time while the time is running. To reset the stopwatch, press set once while the time is stopped.
In alarm mode, the up button turns the alarm on and off. There are three alarms available. To cycle though alarm times, press set. To set an alarm, press and hold set until the time flashes, then set the alarm time using the up button, cycle through hour and minutes using the set button. When finished, press set again.
Timer mode. To set the timer time, press and hold set until the time flashes. The timer goes up to 23h:59m:00s. You cannot set seconds. Once set, the timer can be started and stopped using the up button. There is no reset for the timer, to start a new timer the time must be manual changed again.
To check heart rate, press and hold mode until PUL is shown, place two fingers, one each on the top and bottom metal contacts for 6-10 seconds to get reading (This works best when not in motion).

press in the mode button lower left or the top may say set hold to set, when blinking hr set number by using the right button set up or down , set press mode again goes to mins, then sec. then day and time. press until all set and all showing corrct numbers. then it is set

I couldn't find the manufacturers' web site but I found the following , which may help;-

The unit automatically receives the time signal everyday at midnight and makes any required adjustment to the time displayed.

The WAVE OK indicator and the Tower Icon on the display will show if the time signal is successfully received or after manually pressing the SET/WAVE button

You can trigger a Signal Receive operation at any time by pressing the SET/WAVE button, which will activate the Signal Search function of the unit.
To Manually Set the Clock
To Set the Year and Date
1. Press SET/WAVE button after setting TIME ZONE and DST
2. Press + or - button sequentially to set the year (holding down the button will change the year at a high speed)
3. Press SET/WAVE button to confirm the year set and start the date process
4. Press + or - button sequentially to set the current date (holding down the button will change the date at a high speed)
NOTE: The weekday changes automatically depending on the year and date

To Set the Time
1. Press the SET/WAVE button after setting the calendar
2. Press + or - button sequentially to set the minutes (holding down the button will change the year at a high speed)
NOTE: Once you the press + or - button, the seconds will reset to 00

To set the 12/24 HR mode and the Temperature Mode
1. Press SET/WAVE button after setting the time
2. Press the + button to toggle between between 12HR and 24HR (military) modes
3. Press the - button to toggle between C and F temperature display mode
4. Press SET/WAVE button to confirm and quit the set mode

Hi hdirkse,

To set the digital time and date on your Timex Ironman, please follow the steps below.

1. press and hold the "set" button for two seconds.

2. Use the "advance" button to reach the correct hour.

3. Press the "mode" button, followed by the "advance" button to set the minutes on your Timex Ironman.

4. Repeat the procedure of pressing the "mode" and "advance" buttons to set the month, date, year and day of week.

5. When you are finished setting the time and date, press the "set" button to save.

Setting an Alarm

1. Begin by pressing the "mode" button until the alarm screen appears.

2. Press the "set" button and use the "advance" button to set the hour for your alarm.

3. Repeat the same procedure to set minutes and seconds for your alarm.

4. When you have finished setting the alarm, press the "set" button, followed by "advance" save and activate your alarm.

5. When you alarm sounds, you can deactivate it by pressing any button on the watch.

Hope it helps.

Thank you for using FixYa.

Citizen Weather Data Clock Settings.
To set time press and hold for 5sec "set" button
Use advance to add days, years, hours seconds.
Press SET to hold.

Hi,

To change any of the settings, press 'set' until 'settings' is displayed, press 'ok', now you can either set the heart rate manually in 'limit set' (press 'ok' to change the settings and press 'set' to change)
or input your personal data to let it choose heart rate settings itself in 'user set' where you input weight, height, age and *** (sadly yes please is not one of the options ;¬) )

if you go to www.polar.fi the user manual is on there if you need more clarification.

Hope that helps,

Andy

time:
hold left button -- hour will appear and begin flashing.
press right button to set.
press left button to advance to minutes, press right to set.

date:
press left -- date will appear. now hold left until day flashes.
press right to set.
press left to advance to month, right to set. then same again for year.

Hi catlady05,

To set the digital time and date on your Timex Ironman, please follow the steps below.

1. press and hold the "set" button for two seconds.

2. Use the "advance" button to reach the correct hour.

3. Press the "mode" button, followed by the "advance" button to set the minutes on your Timex Ironman.

4. Repeat the procedure of pressing the "mode" and "advance" buttons to set the month, date, year and day of week.

5. When you are finished setting the time and date, press the "set" button to save.

Setting an Alarm

1. Begin by pressing the "mode" button until the alarm screen appears.

2. Press the "set" button and use the "advance" button to set the hour for your alarm.

3. Repeat the same procedure to set minutes and seconds for your alarm.

4. When you have finished setting the alarm, press the "set" button, followed by "advance" save and activate your alarm.

5. When you alarm sounds, you can deactivate it by pressing any button on the watch.

Hope it helps.

Thank you for using FixYa.