Question about Kodak Office Equipment & Supplies

1 Answer

Kodak U9 error code. How do you clear it? - Kodak Office Equipment & Supplies

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

We are facing problem Kodak i4600 scanner error u9 .we replaced udds Sensor same problem.

Posted on Jul 22, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ar 5631 u9-99 error. how can I clear the fault


It depends on whether you can supply Fixya with more details.
What is the device?
What is the Make?
What is the model?
The code by itself means nothing.

Nov 18, 2017 | The Office Equipment & Supplies

1 Answer

To to clear f2,f6,u2 and u9 sharp Ar235 error code.


go to the simulation 14-0/16-0 and 24-7, the simulation is # interupt c interupt

Jun 13, 2011 | Sharp AR-235 Copier

1 Answer

Error code 3825


Answer: Answer last updated:11-17-08 Error code resolutions are updated on a regular basis. If, after you search, you cannot find a resolution to your error, the instructions below can help you.
IMPORTANT: Print this page before continuing.
Search for a resolution to your specific error code:
  1. Go to KODAK EASYSHARE Software Support.
  2. In the box under Find Answers, type the complete error code (without spaces), then click Search. An example is 12x413x1304x
If you don't find information for your specific error, follow the instructions below:
If the error occurred when you were installing or upgrading EASYSHARE Software:
  1. Uninstall your current version of EASYSHARE Software:
    1. Select Start > Settings > Control Panel > Add or Remove Programs.
    2. Click KODAK EASYSHARE Software.
    3. Select Remove.
    4. Follow the instructions to remove the software.
  2. Go to the Clear Utility for KODAK EASYSHARE Software at www.kodak.com/go/clear, then follow the instructions to run the utility.
  3. After restarting your computer, go to KODAK EASYSHARE Software at www.kodak.com/go/easysharesw, and install the latest version of software, free of charge.

If the error occurred when you were trying to use a feature of EASYSHARE Software:
  1. Run the Repair utility:
    1. Select Start > Settings > Control Panel > Add or Remove Programs.
    2. Click KODAK EASYSHARE Software.
    3. Click Change.
    4. Click Next.
    5. Select Repair, then follow the instructions.
  2. Try the feature again.

Nov 03, 2010 | Office Equipment & Supplies

2 Answers

Error code: 1 2007 esp 5 kodak what is this


Try to uninstall and reinstall the driver.. Run also the clear software of Kodak located at this site www.kodak.com/go/clear

Aug 17, 2009 | Kodak ESP 5 Printer

1 Answer

Error code 1-2036 on Kodak ESP3 printer


this error code is for printer scanner. run clear utility from www.kodak.com/go/clear
and reinstall kodak software from
www.kodak.com/go/downloads.

Note-  Do not connect your printer while installing the software untill installation wizard say to do so.
MS

Jun 14, 2009 | Kodak ESP 3 Multifunction Printer/ Copier/...

1 Answer

The air conditioner wasn't on and the control box was displaying a U9 error


u9 error code means there was a problem with voltage to the unit.Can be caused be either overage or a shortage. Have you had any power outages?

May 12, 2009 | Heating & Cooling

1 Answer

WORKCENTRE PRO 420 U9 CODE


Hello sir; The U-9 code means the main control unit/switch board problem, replace it.

Feb 07, 2009 | Xerox WorkCentre Pro 423 Copier

1 Answer

Rank xerox 5328 U9


if its a u9-1 code it is the lamp that is faulty. Sometimes it can be the connections either end of the lamp but normally the lamp itself. It will probably cost as much to fix as it would to get a new one to be honest

Nov 03, 2008 | Xerox 5830 Copier

1 Answer

Xerox 5328 copier error


U9-3
Xerographic process problem.

The Exposure sensor detected low Exposure Lamp intensity. Switch the Main Power Switch off then on in order to clear the Status Code. Go to the U9-3 Xerographic Process Problem RAP

U9-4
Xerographic process problem.

The Main PWB sensed that the Toner Dispense Motor was not running. Perform 20-3 U Codes Clearance . Go to the U9-4 Xerographic Process Problem RAP

U9-5
Xerographic process problem.

The CSDC zero point was too high during auto setup. Perform 20-3 U Codes Clearance . Go to the U9-4 Xerographic Process Problem RAP U9-5 Xerographic Process Problem RAP .

Aug 09, 2008 | Office Equipment & Supplies

2 Answers

Error code U9


hi im jules_09,are you sure its an error code?chek first all sensor on front door and other parts of the copier that has a sensor,

Nov 02, 2007 | Office Equipment & Supplies

Not finding what you are looking for?

Open Questions:

Office Equipment & Supplies Logo

Related Topics:

2,371 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Office Equipment & Supplies Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Clive
Clive

Level 3 Expert

4345 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Kodak Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...