Error code c -3452 is coming but run the machine code was come on stand by position and i reset the code and machine is running but after some time the code is coming please help me thanks

If you wish to get some details; check the site linked here. Pull up older posts......
http://electro-medical.blogspot.com/

It sounds like a problem with the control board. To reset the codes follow these instructions:

1. Close the door.

2. Turn the knob to 6 o'clock position.

3. Wait 2 seconds.

The start/pause should begin flashing.

4. Press and hold the spin button.

5. Turn the knob to 7 o'clock position.

Wait 2 seconds.

6. Release the button.

7. Turn the knob to off.

This should erase the error code and get you running again.

If the error code returns, you have a problem with the motor, wiring or main control.

If the machine won't go into diagnostics to erase the error code, it would suggest a faulty control board.

Try it several times to see if you get it reset.

Hope this helps.
Bob

Do a cold start....unplug for 5 min.....this should reset the error code...if it returns trouble shoot that area.......

try only once
If the code comes back, you need a Fusing unit. Which will be expensive!!! Sorry :( DO NOT KEEP TRYING TO RESET THE MACHINE! THE MACHINE IS TELLING YOU THERE IS A PROBLEM!!!!! A Fire could occur and that would ruin a perfectly good day!!!!



1. Turn OFF the Main Power Switch.
2. Turn Main Power Switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the Main Power Switch, turn it on again more than 10 seconds after
and check if the machine starts correctly.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Pull the error codes.

To retrieve fault codes:

With engine run/stop switch in the RUN position, hold odometer reset button while turning ignition switch to ON position.

Speedometer back lights wil come on, needle swings to top speed position, indicator lights will come on.

Release reset button.
"diag" should display in odometer.
Push and release odometer reset button. The letter "P" will flash (ECM/ICM info obtainable).
Record any error codes. If none are present, "NONE" will scroll across screen.

Press and hole reset button for more than 5 seconds to go to next mode ("S" = TSM/TSSM/HFSM mode).

When done with all modes, switch off ignition.

Either look up codes in manual, or repost here.

Restart the machine.If code removes then its OK, otherwise press the utility/counter button and restart the machine.Don not leave the button.Keep the button pressed.Trouble reset will appear on screen hit it and restart the machine.

These could be related problems, however I doubt that they are. The error code 3452 refers to thermistor not reaching temp within specified 30 second time frame. There is a sensor there that monitors this. Touch screen may not work due to error code. However, I'm a little suspect that it may be a different problem. But first, let's solve the initial issue and then move onto the screen.
Try clearing the error code first, and then if it appears again, you'll need to look at replacing either the sensor or thermistor. If you are not a certified technician, but attempting to resolve yourself, I would suggest sending the fuser back to whomever you purchased it from and telling them to supply you with another one. During rebuild they probably did not properly gauge the sensor from the fusing roller. therefore it is not able to properly monitor temperature. (very common problem)....
Here is the instructions for clearing the error code:

1. Turn OFF the Main Power Switch.

2. Turn Main Power Switch ON again while holding down the Utility/Counter key more than 10 seconds after. A screen will appear saying "TROUBLE RESET"

3. Touch "TROUBLE RESET".

4. Check to make sure that "OK" is displayed below which confirms it has been reset.

If "OK" is not there , it will show a different code....

IF it says "OK", you should be good to go. Error code should now be cleared.

5. Just Turn off the Main Power Switch wait at least 10 seconds....and turn it on. Make sure that the machine properly starts.

** If it re-displays the code again within a short period of time, replace the fuser unit. Or get a certified technician to replace the or adjust the sensor or Thermistor unit. However, since you just purchased this I will assume that it is either a defective unit from manufacturer, or the company who rebuilt it did not properly ensure it was working. Return it and demand a replacement in EITHER case!! J

Hope this helps

develop ineo 250 machine error comes c3452
how i solve this

This service code C0070 is a universal code used by Konica Minolta to indicate a toner bottle rotation failure. These machines add toner by rotating the toner bottle that you install in the machine. Most of the time this code is caused by a toner cartridge that has been installed incorrectly or has become dislodged from it's holder. To clear the code open the toner door and remove the toner cartridge/bottle from the machine. Close the toner door and turn the machine off then on to reset the code. Let the machine run. This may take several minutes and will allow the machine to bring the toner bottle receptacle into it's home position. Once the machine stops running completely, then you can re-install the toner cartridge. If the code does not come back you are ready to go. If the code came back after removing the toner but before you re-installed it then you have either a dirty rotation sensor or a bad toner drive motor and will need service.
If the code comes back after the cartridge is re-installed then there is either a priblem with the cartridge or with the toner bottle drive.
Most of the time though the problem will be resolved by the outlined procedure.
Good Luck and Thank You for using Fixya.

It could be several things but when it does it again try loosening you fuel cap and see if it starts,also check the cam and crank shaft position sensors,if your scan tool has a stand alone feather try having hooked to the truck when you are having this problem,before the truck actually starts some times the codes are reset once the trucks computer catches back up and resets to running smooth.good luck