I have model WT:8029U solar power clock. How do I set it to Mountain Time?

I don't have specific information about the Model 65904 Ecotech solar clock, but here are general steps you can try to set the time and date on a typical clock:
1. Locate the Time Setting Button:
- Look for a button that is labeled "Time Set" or similar. This button is often located on the back or bottom of the clock.
2. Press and Hold the Time Setting Button:
- Press and hold the "Time Set" button until the numbers on the clock display start flashing or blinking. This indicates that you are now in the time-setting mode.
3. Adjust the Time:
- Once the numbers are blinking, use the "+" or "-" buttons to adjust the hours and minutes. Some clocks may have separate buttons for hours and minutes, while others may have a single button that cycles through hours and minutes.
4. Set the Date (if applicable):
- If your clock displays the date, you may need to follow a similar process to set the date. Look for a "Date Set" button and adjust the date using the same method as adjusting the time.
5. Confirm the Settings:
- After setting the time and date, press the "Time Set" or a similar button again to confirm your settings. The blinking numbers should stop, indicating that the clock has accepted the new time and date.
6. Check for Other Settings:
- Some clocks may have additional settings, such as a 12/24-hour format or a daylight saving time (DST) adjustment. If applicable, use the appropriate buttons to configure these settings.
If these general steps don't work for your specific clock model, I recommend trying to locate the user manual or contacting the manufacturer directly for assistance. Manufacturers often provide manuals on their websites, or they may be able to assist you with setting the time and date over the phone.

Hi Mary
To set the timezone:

• In the Normal Time Display, press the [MODE] button to enter the Alarm Time Mode.
• Press the [SET] button to set the desired time zone. Refer to the Time Zone map on the display, P=Pacific, M=Mountain, C=Central and E=Eastern.
• Press the [MODE] to return to the time mode position.

Full instructions for all of the clock features can be found at the following link:
Instructions Warranty for Atomic Clock Model SPC364

Trust this helps
Regards
Alan

easiest way to set clock time. Remove AA battery's if installed.
Unplug Clock from AC. Wait a few seconds. Then replug clock into AC power. Clock will now flash 12:00. Press hours button until correct time is set PM has led on AM has Led off. Set minutes to correct minutes. Then press alarm reset / power/mode button. Wait a few seconds and display will show correct time. Now you can put the AA batteries back in.

Press and hold the "UP" button for three seconds. Repeat until you hit your zone.

It sets itself. You just tell it the Time Zone. http://www.klockit.com/PDFs/lacrossemanuals/AnalogWallClocks.pdf

Check both of these

Daylight Saving Time Automatically Updates (DST) (On/Off Option) applies to both USA and UK

U.S. Time Zone Selection: Eastern, Central, Mountain, Pacific (applies to USA only)

Hi,

Hope this will helped you fixing the time of your Citezen divers watch. Just foolow the instruction below.

Change your Citizen watch's time zone without actually moving the clock hands. On the digital display, change the city that displays on the watch, which sets the time to the different time zone. The Citizen also has a calendar, timer, chronograph and LED lights. Since it is an Eco Drive watch, it is solar powered so you never have to replace the batteries unless its backup power source dies.
Difficulty: Easy Instructions

1. Pull the setting knob (crown) out one "tick" for setting mode.
   

2. Set the mode hand to "WT-S."
   

3. Pull the crown out one more "tick."
   

4. Press the top button on the right side of the watch for the city setting mode.
   

5. Press the lower button on the right side to "SET" the city.
   

6. Turn the crown to select a different city, which changes the time zone.
   

7. Push the crown all the way back in to finish setting the time.
   

Thank you for using Fixya.

Press the Mode button to display the alarm time then press the Adjust button till you get tot the corret time zone, press Mode again once have found the coreect timezone.

http://www.lacrossetechnology.com/2171/manual.pdf

Simple to fix

Try this link and follow the instructions.

http://www.lacrossetechnology.com/3143a/manual.pdf