Question about Washing Machines

1 Answer

Shakes during spin cycle

The washing machine washes as normal but when it goes to the spin cycle the entire machine shakes so bad that it vibrates everything.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 109 Answers

Most out of balance problems are from the clothes in it. Stop it, move the clothes around - kind of even out the load and try again.

Posted on Mar 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Admiral washer machine tub appears loose and unattached in rrear


First of all is your machine working or not?
If it is working and it's a front loading machine. The machine drum is hanging inside the machine using strong springs that helps it to reduce vibrations during washing and spin cycle.
When machine goes into spin(dry cycle), it usually shakes a little.

Dec 08, 2014 | Admiral Washing Machines

1 Answer

Sharp washing machine,ES-AG950 hangs during the spin cysle.


Sounds like its tripping the drum vibration sensor or a temp limit sensor on your motor.

Apr 09, 2013 | Washing Machines

1 Answer

LG front loaded washing machine vibrates during


If its on a pedistal then that will raise your center of gravity and cause the unit to be less sturdy during a spin. It could also be due to a weak floor. You may want to try a product called "shake away pads". The probably sell them at like home depot or lowes. They will run you about 40 bucks but they just go under the legs and help absorb some shock. Good luck _MJ_

Apr 27, 2010 | LG WM2487H Front Load Washer

2 Answers

Washing machine wont drain keeps bleeping ERR2


It will not spin with water in.
See if you can locate a filter, and clean same.

Jan 19, 2010 | Haier Washing Machines

1 Answer

Violent spin cycle on the Frigidare front-loading washer


I assume you bought it new, so on that basis, did you remove the transit packing materials inside the machine ?

Front loading washing machine normal design is for the drum assembly to be supported by two or more springs at the top, and two dampers at the bottom. This allows the drum to move in a controlled fashion and also minimises vibration, particularly during spinning.
When the machines are shipped from the factory, transit packaging is put inside the machine to ensure that any shocks to the machine during transit dont damage the springs or dampers. This must be removed before use otherwise you get pretty much the symptoms you describe.

The manual that cam with it will show you how to remove the transit packaging. In such a short time I suspect you wont have suffered any damage, but take the transit packaging out as soon as possible.

Nov 04, 2009 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Washer vibrating badly


Hi, Try these
  1. Balance the load
  2. Level the machine
  3. Inspect the water pump for a blockage
  4. Inspect the coupling
  5. Inspect the transmission
  6. Adjust the drive belt tension
  7. Check the motor bearings
  8. Check the drum brakes
pls rate my suggestion......

Jul 19, 2009 | LG Washing Machines

1 Answer

Excessive shaking


your suspension dampers is damaged on washing machine causing bad balance on spin cycle..

Mar 03, 2009 | LG WM2277HSW XL Front Load Stackable...

1 Answer

Maytag Neptune Series MAH5500BW loud noise during spin cycle.


very loud in spin cycle can mean a bad rear bearing, not something a homeowner would want to try to replace, parts would exceed 6-7 hundered dollars. you may have some extended part warr through the manufacture. still probly gonna be a 5 hundred when the labor is added in

Dec 06, 2008 | Maytag Neptune Washer

2 Answers

Unbalanced load


If your washer goes severely off balance you need part # W10112113 to fix it.

Nov 25, 2007 | Whirlpool Cabrio WTW6600SBT Top Load...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

455 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85108 Answers

Brad Brown

Level 3 Expert

18067 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...