Question about Pride Mobility Products New Pride Mobility Jet 3 Ultra Power Wheel Chair

3 Answers

Lights just flash on controller and wont move jet 3 wheel chair

Lights just flash on controller by joystick and it wont move or do anything jet 3 wheelchair help!!!

Posted by on

  • 3 more comments 
  • Anonymous Mar 30, 2009

    they just keep flashing and i dont really see a pause it it

  • Anonymous May 20, 2009

    red and amber lights flash

  • karen dennis Jun 13, 2013

    no it doesnt pause it just flashes all the time

  • Anonymous Mar 20, 2014

    Where can i find the left motor, my machine has 2 red lights flashing, I was told it was my left motor perhaps, chair will not move

  • Anonymous Mar 27, 2014

    joystick clicks on but wheels will not move
    power to joystick , but clicks down at the wheel

×

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 40 Answers

Do they flash in series? Like ten flashes then a pause then ten flashes?

Posted on Mar 30, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 317 Answers

Get the Pride Toubleshooting Instructions at PrideMobility.com. The lights are Diagnostic Flash Codes. Look up the code and it will advise you of the cause of the problem and possible solutions.

Posted on May 15, 2013

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

My own jet 3 lights flash if the chair is idle for 4 or 5 minutes.I think it is a power saving feature.
When I want to move again I press the ' power' button twice and off it goes.
Joe

Posted on Oct 31, 2012

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 7 Answers

SOURCE: lights just flash on controller and wont move jet 3 wheel chair, it is the secondd row of ligths on the controller, the ones that indicate speed. They are flasing steadily

Check that you don't have the charger cord still connected or the motor disengaged.

Posted on Jun 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why controller light flashes but wont work


Flashing lights on a controller are showing you a trouble code. To find out what the code means, count the blinking LEDs.
Here's a link to Pride's troubleshooting guide for the Jet 3:

http://www.pridemobility.com/includes/download.php?f=troubleshooting/INFINFB2045_Jet_3_Ultra_Troubleshooting.pdf

Feb 05, 2015 | Jet 3 Ultra Power Chair

1 Answer

When I turn on controller power the speed lights flash slowly. Joystick does nothing and chair is dead. Chair is Pride Jet 3 Ultra.


Do all of the speed lights flash at the same time or do they ripple from left to right? If they ripple from left to right the chair is in lock mode and you can use the unlock procedures from my tips to unlock. If they are all flashing at the same time you have an internal joystick problem and the joystick needs to be replaced Hope this helps

Apr 27, 2011 | Pride Mobility Products New Pride Mobility...

1 Answer

How do I know if my jet 3 ultra is charging? I just bought a used one today and do not have a manual


The chair should have a meter on the rear panel where the 9 pin connector for the joystick plugs into the chair when you plug in the charger cord the meter should move up and the lights on the joystick should flash indicating the charger is plugged in. When the chair is fully charged the meter should read zero or bounce up and down. Hope this helps

Feb 02, 2011 | Jet 3 Ultra Power Chair

1 Answer

Wheel chair won't move. Batteries have been charging for several hours and have some charge but chair will not move.Any suggestions? Thanks


Romp, Did you check the freewheel levers chair will not move if you are in freewheel. Levers are in front next to seat posts and need to be facing forward. If you are not in freewheel then check the number of lights you have on on the joystick and that they aren't flashing. Also check that your speed control is not on the lowest setting even with some charge a slow speed setting will not let the chair move. Now by some charge you mean lights in the green on the joystick? If the lights aren't flashing then I'm kinda unsure other than even with some charge the batteries don't have enuf current to drive the motors and need to be replaced Hoe this helps

Aug 22, 2010 | Pride Mobility Products New Pride Mobility...

1 Answer

When switched on power light flashes.


How many flashes? Count number of flashes should be a slight pause then flashes the same number of times . Your manual will give you flash codes and you can determine what the problem is. If all the lights are flashing and there is no pause the chair could be in "lockout" Your manual should tell you how to get the chair out of lockout I think that Pride uses the joystick to get it out of this mode.. Turn the chair on move the joystick forward till you hear a beep then move the joystick to the rear until you hear another beep release the joystick and the lights should quit flashing Hope this helps

Aug 12, 2010 | Pride Mobility Products New Pride Mobility...

1 Answer

I have a power chair it is a jet 3 ,the lights flash , i know there is a code to reset it , so can you help me. i have had it repaired before and they just reset it but i need to now how,


Hi. Different numbers of LED's flashing mean different faults.
Your machine can be in "lock " mode.
To unlock it, turn the machine on.
Move the joystick full forward until it beeps.
Then move the joystick full reverse until it beeps.
The machine should then work normally.
If you still have flashing LED's, count the flashes between the pauses, and let me know.
Good luck. Neil.

Jul 05, 2010 | Jet 3 Ultra Power Chair

1 Answer

Jet 3 power chair power lights just flash, no sequence of flashes


hold joystick back, press on button, move joystick forward, then let go.

Feb 17, 2010 | Jet 3 Ultra Power Chair

1 Answer

All six lights blink on my Jet 3


I just had the same problem with my uncle's power chair. The number of "blinks" indicates a problem code to the technicians. My chair needed the joystick control assembly replaced. Once replaced, evrything was back to normal. 'Not a cheap fix but much needed. Good luck my friend!!

Apr 28, 2009 | Jet 3 Ultra Power Chair

Not finding what you are looking for?
Pride Mobility Products New Pride Mobility Jet 3 Ultra Power Wheel Chair Logo

2,986 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pride Mobility Products Health & Beauty Experts

Rob Hill
Rob Hill

Level 3 Expert

1367 Answers

Will

Level 1 Expert

25 Answers

Marvin
Marvin

Level 3 Expert

85020 Answers

Are you a Pride Mobility Products Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...