Menu wont work, continuos channel search

Hello
First connect the cable to its cable input socket at rear.
Turn the tV On and enter its Menu option window. Press UP or DN button on the remote control to select 'Cable'. Selecte EZ scan [channel search]. The TV must scan for all available channels, and will stop after all the channels has been stored in its memory. You have to wait till the search function stops; no other functions with remote cannot be done, and the set will not respond any external command, either by remote control or by its front panel control, except the mains power ON/OFF switch will work. OK.

1. Manually turn on the tv.
2. Hold code search button until the red light stays on.
3. Press and release TV button-the light should blink
4. Enter one of the following codes:517 419 512 613 719 112 506 111 618 627 437 041 891 802 111 313 715 With a valid code entry, the light should turn off.
5. Press channel up button. If the tv responds, the code worked.

If some functions (like mute or menu) dont do what they should, try a different code.
Good luck.

Hello
Codes for Emerson TV with RCA- RCU 600 are

..........004, 006, 012, 023

..........024, 025, 026, 027, 028, 029

..........030, 031, 032, 033, 034, 035

..........036, 037, 038, 039, 041, 042

..........043, 044, 046, 047, 123, 124
162, 171, 177, 179, 191, 196, 208

1. Manually turn on the TV.

Find the three digit code for your TV in

the code list below.

2. Press and hold the CODE SEARCH

button until the INDICATOR LIGHT

lights, then release the CODE SEARCH

button.

3. Press and release the TV button (The

INDICATOR LIGHT will blink then

remain lit).

4. Enter the code using the Number

Buttons.

After your code is entered, the

INDICATOR LIGHT will turn off. If the

code is not valid, the INDICATOR

LIGHT will blink. Check the code list

and repeat process.

5. Aim the remote at your TV and press

the ON•OFF button. Your TV should

turn off.

Note: If your TV does not respond, try all the

codes for your brand. If the codes do not

work, or your brand is not listed, try the Code

Search method on page 16.

6. With your TV on, press CH+ (CHANNEL

UP) If the TV responds, no further
programming is required.
OK

This is caused by radio frequency and what i mean by that isyour tv unit is gettng confused with the crystals that control the connection between the tv and remote.The solution to this is to go to wal mart and buy a new universal remote and in the package should be an instruction manual to set the remote to the tv , First find your tv name in the pamplet,second there will show a code of the remote type it in and enjoy.

It's only thru your remote. try fixing your remote control.
Take off the battery, open the back of your remote, lift the circuit board, clean the green painted part with cotton balls slightly damp with rubbing alcohol as well as the black thingy behind your remote pad, let it dry put it back together, replace with a new battery and try if it works.

Here you go. This will work with most all universal remote controls. If you don't have the code do the following:
Automatic Programming
With automatic programming, the remote control tests all the codes available on the Code List and assigns the correct code for the selected device. Although this method can be more time-consuming, it eliminates the need to look up codes and enter them manually.

1. Turn off the device with which you want to use the remote control.

2. Press and hold the corresponding button on the remote control
(TV, VCR, SAT, DVD, CAB or AUD) until POWER INDICATOR illuminates. It should take a couple of seconds for the light to remain solid. The remote control is in programming mode.

3. Press and release power button. The POWER INDICATOR flashes once and stays on indicating the unit is in Power Scan mode.

4. Press CHANNEL up or CHANNEL down repeatedly until the device turns on.

5. When the device turns on, press OK to store the code.

Note:
• To exit without storing the code, press BACK.
• T he unit will search for the next code or the previous code if you press
CHANNEL up or CHANNEL down after the device turns on. (go slow you need to press OK when the TV turns on) if you mess up turn TV off and start over.
6. Press any other button. If the device responds, the remote control has been programmed. If the device does not respond, repeat steps 2-5.

Fill free to ask me questions about anything..........................

Here you go. This will work with most all universal remote controls. If you don't have the code do the following:
Automatic Programming
With automatic programming, the remote control tests all the codes available on the Code List and assigns the correct code for the selected device. Although this method can be more time-consuming, it eliminates the need to look up codes and enter them manually.

1. Turn off the device with which you want to use the remote control.

2. Press and hold the corresponding button on the remote control
(TV, VCR, SAT, DVD, CAB or AUD) until POWER INDICATOR illuminates. It should take a couple of seconds for the light to remain solid. The remote control is in programming mode.

3. Press and release power button. The POWER INDICATOR flashes once and stays on indicating the unit is in Power Scan mode.

4. Press CHANNEL up or CHANNEL down repeatedly until the device turns on.

5. When the device turns on, press OK to store the code.

Note:
• To exit without storing the code, press BACK.
• T he unit will search for the next code or the previous code if you press
CHANNEL up or CHANNEL down after the device turns on. (go slow you need to press OK when the TV turns on) if you mess up turn TV off and start over.
6. Press any other button. If the device responds, the remote control has been programmed. If the device does not respond, repeat steps 2-5.

Fill free to ask me questions about anything..........................

Codes for Samsung (one of them should work on your RCA remote)

006,011,014,015,019,027,036,037,077

Programming Your Universal Remote.

The remote may already be set up to operate your brand of TV, VCR, or Cable Box. It is pre-programmed with following codes:

• TV-000
• VCR-000
• Cable Box-000
• AUX is programmed with VCR code 037

For brands that require programming, there are two ways to program: Using Code Lists or Code Search. Use Code Search if the code lists are not available or if the codes from the lists do not operate a device.

Programming a Device using Code Search:

1. Manually turn ON your device (TV, VCR, Cable Box)
2. Press and "HOLD" CODE SEARCH
3. Press and release the device button you want to set up (TV, VCR, Cable Box) However, if you are using AUX for a device, press and release AUX first and then the device button for the type of device to be programmed (TV, VCR, or Cable). The selected device button will flash once.
4. Release CODE SEARCH.
5. Press OFF/ON repeatedly until the device turns off (you may have to press up to 100 times at a rate of once per second).
6. Once the device turns off, press and release ENTER.
7. With the device on, press any other button. If the device responds, no further programming is required. If the device does not respond, repeat steps 1-6.

Programming a device using the Code Lists:

1. Find codes for each device and brand below.
2. Press and "HOLD" CODE SEARCH.
3. Press and release the TV, VCR or Cable button you want to set up. If programming AUX for a device, press and release AUX first and then the device to be programmed (TV, VCR or Cable). When the selected device button flashes proceed to the next step.
4. Enter the three digit code from the TV, VCR or Cable Box code lists.
   
   
5. Release CODE SEARCH.
6. With the device on, press another button, for example CHANNEL UP. If the device responds, no further programming is required. If the device does not respond, repeat steps 1-5 using another code number from the lists.

You must get a proper replacement remote control, once you can access the menu and find you cannot store above 13, place another post and i will help you further.

you need to program your remote control. take the battaries out. and maually turn the tv on. then hit the source you want to view. for example, I want to control the tv set. I push, code search and hold it then push the source button and then release the source button and then release the code search button. now, aim at the tv and then keep pressing power button till it goes off. when the tv is off, hit return or set or something like that.( every remote has different calling for it but still the same function) it should work. try it and let me know.