Ultrafit treadmill error code e1

If the E1 error occurs after the belt starts to move for several seconds, the error code means that the system is not picking up the speed of the motor. This pickup comes from a magnet mounted on the front roller pulley and a speed sensor, or a problem with the magnet.Feb 29, 2016

E1 Error Codes - The Treadmill Engineer

treadmill-engineer.com http://www.treadmill-engineer.com > 2016/02 > e1-error...

Reebok ZR9 treadmill has E01 error on console since ...

JustAnswer https://www.justanswer.co.uk > electronics > ca4k2-ree...
Reebok ZR9 treadmill has E01 error on console since moving · 1. Turn the machine off at the mains socket for at least 30 seconds · 2. Turn the machine on at the ...

• 
  

  I have a Rebok ZR8 treadmill that displays an E01 error

  https://www.justanswer.co.uk > fitness-equipment > dwrp...
  It is the internal sensor tr the mainboard that has faulted. I am really sorry about this and you are going to have to return the unit to have these tested and ...
  
  

..

this will help you. http://www.treadmill-engineer.com/2016/02/e1-error-codes.html

Replacement Parts for Fitness Exercise Equipment at SPORTSMITH

True Treadmill Errors and Service Messages

• The True 600, 700, 725 and 750 series treadmills are equipped with built-in diagnostics and maintenance reminders that display either an error message or service message as they occur.
• The error messages that may be displayed by the built-in diagnostics are as follows:
  • E1:INCLINE
  • This means that the incline is moving when it has not been commanded to.
  • E1:MINIMUM
    • This is a minimum incline calibrating error that can be cleared by calibrating the incline.
  • E1:RANGE
    • This means the difference between the treadmills zero position and maximum incline is not sufficient.
  • E1:STALL
    • This means that the incline is not moving when it has been commanded to.
  • E2:OVERSPEED
    • This occurs when acceleration greater than 2.1 mph occurs as this is greater acceleration than anticipated.
  • E2:CAL
    • This means feedback cannot reduce or increase speed to target and error can be cleared by calibrating treadmill.
  • E3:EEPROM
    • This error happens when a data error is detected on the EEprom. The control panel needs replaced if this error occurs.
  • E5:SENSOR
    • This error occurs when there is no speed or RPM feedback detected from speed sensor.
• The service messages that may be displayed by the built-in maintenance reminders are as follows:
  • S1:LUBE
  • This service message displays when it is time for inspection of the deck lubrication system.
  • S2:CLEAN
    • This service message displays every 500 miles and is your prompt to clean the treadmill.
  • S3:MOTOR
    • This service message displays every 2500 hours and is your prompt to check the motor brushes.
• This information should help you understand the cause of the error message or code and how to take action to repair your True treadmill

Errors for True Treadmills E5 Sensor E2 Cal S1 Lube and more

Remove up and down liver moter cabel in mother board. And restart machine. Now ok e1 error.

Is it possible to disable the e1 error code. Trying to repurpose motor.

Adjust the reed switch as indicated by the diagram by 1/8- 1/4". Run the calibration software instruction under the Hood motor or see your user manual.

sincerely.
ernesto cuadra
managua, nicaragua. c.a.

My motorized Treadmill is showing error E09 how can l clear the error?

1)probably a faulty speed sensor
2) speed sensor is not plugged in properly.
3)possibly a faulty motor
4) Main control board or lower board.
The error codes will differ between makes and models but could be e1.
Check this video for speed sensor.
http://www.youtube.com/watch?v=23ZgWaVEQjA

adjust the speed sensor:Move the motor to slacken the pulley, then lift the motor to get underneath. That is where the treadmills speed sensor will be located. It is usually a square or rectangular shaped green module with connectors at both ends.

Finally after you did the adjustment you can conclude:
A) Faulty Speed sensor B) Main Motor faulty C) Main Motor Controller faulty.

attached block diagram for treadmill that I did for any treadmills,see how the Main Motor Board has function for 90% of the treadmills.
sincerely.
E.CUADRA
MANAGUA, NICARAGUA. C.A

Lets eliminate the motor first, unplug unit remove motor shroud fin the 2 leads from motor to lower board. Connect a 18v DC battery to the leads this start the motor to move at approx. 1 mph if it does motor is good,if not you may worn motor brushes worst case open connection in the motor.
Now if the motor is good then reconnection the leads and plug in unit the lower board should have some LEDs lit up. Now find the LED that says PWM start unit if that light should start to flicker then the upper board and wire harness are work properly. Turn off the treadmill then turn it on and with a multi meter insert the leads into the connectors that go to the motor, then put the meter on 200v DC then start the treadmill you should get a reading 5 to 10v DC if you get 0v DC then the board will need replacing

Trimline treadmill starts up then code E2 comes up, and the display shuts down. 
Any ideas???