Question about Fisher and Paykel Fisher & Paykel Washer

3 Answers

Fisher paykel smartdrive 601

My fisher Paykel smartdrive 601 is beeping continuously before the rinse cycle and won't move on to the rinse cycle. I have tried turning it off and pulling it out of the wall, but it doesn't help.

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Most likely a blocked pump

Posted on Apr 19, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 72 Answers

Mabee ??? mine had the same problem and the water level switch thru inspection they have a resin coated resistor or cap loses continuity so what i did was put 2 cable ties across the legs and tighen them to pull them closer together =0=
l l and worked like a charm but also blow back thru the hose by mouth to see if its not blocked fit hose on good
let me know how you go

Posted on Apr 18, 2009

  • chippit
    chippit Mar 23, 2010

    Ok so mine was a temporary fix finally it crashed and burned so i bit the bullet and ordered a new module 190 bucks from f&p brisbane plus delivery now they assholed the old modules and have the new ones but i also checked the pump ohm first should be 33 ohm watch the clip that holds them in and ist up and running dont forget to reset the bowl level read the paper that comes with it

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 144 Answers

I can talk you through diagnostics if you want to go on live chat cheers

Posted on Mar 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Fisher and Paykel Smartdrive 9 washing machine that won't fill. It starts then stops and continues to do so, then stops altogether and beeps. Can anyone help??


The error code is displayed when its beeping.
I don't know the error code, so It can only be three things,
Out of balance switch,Lid magnetic reed switch,Or Rotor position sensor,Your error code would help me work out witch one of these are faulty. to work out your error code look at picture below.
Add up the lights that are on.
2_11_2013_1_58_23_pm.jpg

Jan 08, 2013 | Fisher and Paykel Washing Machines

1 Answer

Hi I have a Fisher and Paykel Smartdrive 601, and the cold water is dribbling out when I put it through a cycle, do you know what the cause is, and how can I fix it??


Your cold water valve is not seating when off,
Try swapping the hot valve for the cold to see if that will fix the problem. if it fixers the problem buy a new cold valve.

Oct 13, 2012 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Fisher Paykel washing machine Smartdrive 703 Advance, Power and Start buttons are non responsive when pushed. Is there a part that can fix this. Does the control panel have to be replaced?


Fisher & Paykel Smart Drive beeps and stops during rinse cycle. If I hit pause and wait and restart it eventually continues. It seems like it has problems detecting water level.

Apr 13, 2011 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

My fisher and paykel smartdrive 708 stops at rinse/spin cycle with machine still full of water


with no error code ... I would check you drain pump or drain hose... you first may want to try a shop vac connected to the end of a drain hose .. let me know if it helps

Dec 15, 2008 | Fisher and Paykel Fisher Paykel Intuitive...

2 Answers

Fisher and Paykel Smart Drive 608 wont spin


remove the pump from underneath front right move whith clip forward the twist pump out.but you will need to remove all the water first you may a ball of lint stuck in the pump.hope this helps.

Mar 29, 2008 | Washing Machines

1 Answer

Fisher n Paykel Smartdrive 9


Most waashers rinse with cold water and if your cold water screen on the valve is plugged and it can't let water in it may cause your problem.

Aug 30, 2007 | Fisher Paykel EcoSmart GWL15

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

1,512 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...