Flashing EFO error code

turbid water!

Whirlpool Dishwasher Error/Fault Codes - eSpares

https://www.espares.co.uk > Advice Centre > Dishwashers
FA (or 11 flashes) - Optical water indicator (turbidity) ... This fault indicates an error with the sensor in your machine that monitors the water cleanliness. If ...

Whirlpool Dishwasher Error Codes - Lights Blinking Flashing

https://removeandreplace.com > ... > Dishwasher Repair
Mar 9, 2016 - Some Whirlpool dishwashers display an error code by flashing the clean Light on the display in a pattern.

Whirlpool ADG 7560/2 pumps in water, then beeps with error ...

https://www.reddit.com > Whirlpool > comments > dish...
3 days ago - Dishwasher - Whirlpool ADG 7560/2 pumps in water, then beeps with error and 11 flashes. My dishwasher started faulting.

..

Good Morning Friend,

I understand that your Frigidaire Affinity washer, model# ATF7000E, is flashing an EFO code. I do not show an EFO code for your appliance.

I do show an EF1 code, which means the drain pump is clogged. In this instance you would unclog the drain pump.

I also show an EF2 code, which means too much soap was used. All you would do for this would be to try using less soap.

It could also be a false error code. I suggest resetting your washer, by either unplugging it or shutting the power off at your homes circuit breaker, for 3-5 minutes. When you restore power, start any cycle on your washer. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your washer status has changed successfully. Hope this is helpful.

-Best Regards-
WP

Hello - This manufacturer does not show to have such an error code for a wall oven. However the error codes F30/F31 indicates that the unit either has an issue with the oven sensor, wiring with the EOC or the probe connections is open or shorted. Contact a professional to move forward accurately.

efo enter prblem what is the problem

EFO is not a Kenmore Error Code.

Zanussi & AEG EFO = Filter Blocked (low flow) and it is accessible from the bottom front of the machine.

1. there is a blockage in the filter or drain hose.takes too long to drain out.
2. over dosing of powder or liquid. again can cause an air lock in the pump which slows the drain pump down.

Check the filter and drain hose and test again. this fault will only come up at the end of a cycle.
You do not need to reset the machine to get rid of the fault code as this is automatically deleted.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

You need to refer to the owners manual in trouble shooting catagory, if you can't find yur answer there contact Fridgadaire ither by phone or e-mail and choose the help section.

Electrolux Washer Fault Code for EFO or EF0

Drain Filter is Clogged. Resolution => Click lint filter for soap buildup or other debris. Check drain hose.

Oversudsing - A high efficiency detergent was not used.
Too much detergent was added. Resolution => Use only a high efficiency detergent. Follow manufacturer's recommendation for dosage. Amount may need to be adjusted for water temperature,
water hardness, load size and soil level.

Hot water doesn't enter washer - Hot water hose is connected to the wrong faucet. Hot water faucet is not turned on. Resolution => Connect hot water hose to hot water faucet and hot inlet on
washer. Be sure hot water faucet is fully opened. Check water heater.

I just spoke with customer support for my Affinity. They told me it was over sudsing (sp?). from using too much soap or not using high efficiency soap. Suggested running thru a cycle without soap to clear things out.

spoke with electrolux and they tell me that it is over sudsing problem. The washer must use HE detergent or use only a the lowest amount on the cup.

It is simple. The wrong soap or too much soap will caused EFO to flash. I overfilled the machine with soap by accident. It started flashing with EFO and I went nuts. What could be wrong with it now?! Too much soap or not the right kind of soap will cause this problem.
Plus, I found a sheet of paper that gives the codes.

This is better than when the strainer plug gets filled up and you have to take the machine apart to clean the little strainer.