Xerox 5230 error fault 010-320

https://printcopy.info/?l=en&mod=erc&brand=Xerox&model=WorkCentre%205225&code=010-327

http://www.copytechnet.com/forums/xerox/120736-workcentre-5230-often-code-010-327-a.html

First, I'm not a Xerox representative.
* Check your warranty. Call for support.
* Official site; https://www.xerox.com/en-us/office/multifunction-printer/multifunction-under-30ppm/versalink-b7025-b7030-b7035/video/1

*** The following is for information only.***
* Copytechnet.com (Forum) answers this question 026-717; http://www.copytechnet.com/forums/xerox/112361-wc7328-error-010-110-026-717-a.html
* Brochure; https://www.office.xerox.com/latest/VB7BR-01U.PDF
* Data; http://www.topedge.ro/info/DATA-SHEET/XEROX/VB7SS-01U.pdf
* Support (note WiFi Setup); http://www.support.xerox.com/support/versalink-b7025-b7030-b7035/video/enus.html?operatingSystem=os2&fileLanguage=en&contentId=139981&from=videos&viewArchived=false
* Admin & Password; https://atyourservice.blogs.xerox.com/2016/10/07/xerox-system-administrator-username-and-password/
* Resolve the Error "Job Held for Resources"; https://www.youtube.com/watch?v=fJ5i3cWcCTw
* Xerox Work Centre 5230 5225 fault code 010 027 solution; https://www.youtube.com/watch?v=_HMld3k_ciQ
* error code 116 365; https://www.youtube.com/watch?v=6dO5ICwZypw
* If your have your WiFi set up then Xerox could offer direct support.
Aloha, ukeboy57

If you wish to get some details; check the site linked here. Pull up older posts...
http://electro-medical.blogspot.com/

That error signifies a defective fuser unit. Replace fuser, part number 126K24980.

http://www.iteminconline.com/126k24980_126k24980-126k24981-126k24982-126k24983-126k24984-xerox-workcentre-5225-5230-fuser-110v-new.htm

Here is a link to the service manual: http://www.scribd.com/doc/86553381/XEROX-Work-Centre-5222-5225-5230-Service-Manual-Pages#scribd

012-132 RAP Finisher Transport Entrance Sensor ON Jam (Long).

That error signifies a defective fuser, not coming to temperature. Replace fuser, part number 126K24980. See link below:

http://www.iteminconline.com/126k24980_126k24980-126k24981-126k24982-126k24983-126k24984-xerox-workcentre-5225-5230-fuser-110v-new.htm

power down machine,
remove drum,
power on machine,
reseat drum

machine show error code of 010-327. how to correct this error

error 010-327

010-150, 155 Too much or not enough paper in duplex tray 10-300 Fuser thermistor 10-302 Low fuser temperature 010-304 Bad fuser temp 10-308 High fuser temperature or open thermistor 010-310 High fuser temperature 010-312 Fuser not up to temperature after energy save 010-314 Fuser problem 010-320 Fuser web finished 010-330,327 335, 340 Exit switch, vertical sensor switch actuated when power is turned on