Maytag Neptune MAH5500B Front Load Washer Logo
Posted on Mar 07, 2009
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Maytag Neptune Washing Machine electronic malfunction.

The machine has a mind of its own! Not responsive to buttons, will not turn off and turns on by itself, changes cycles on its own. A service man indicated that the motherboard needed to be replaced and would cost over $450. Question? Can I purchase the non garanteed motherboard part and install it myself to save money. or should I purchase a new (need recommendation) washing machine?

We are considering the Whirlpool duet 4.0 and the Miele ($$$$)?

  • Anonymous Mar 15, 2014

    Program buttons are not working.. Not accepting any command & no response in Led indications

×

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.

  • Master 878 Answers
  • Posted on Mar 07, 2009
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.

Joined: Apr 16, 2006
Answers
878
Questions
1
Helped
1201967
Points
3312

Barry, sounds more like the keypad is stuck or shorted. You can try to do a membrane test by putting it into the service mode. Have the unit on, press and hold the delicates and heavy soil key together until it shows 00 on the display. Then press the wrinkle free key. This will let you test every key on the keypad. You can toggle them off and on and see if they are responding. If they are not responding then you can assume that the keypad is your problem. At repairclinic.com you can order the part you need and if it doesn't solve the problem they will take it back no questions asked. A lot of people are not too fond of these washers because of the many issues they had with them. You would have to weigh the price of the part versus a new washer. The keypad is not hard to install. Just a ribbon that plugs into the board. You may want to try to clean the end of the ribbon with a eraser and see if that fixes the problem. Make sure the unit is unplugged before going in there.

  • Anonymous Mar 09, 2009

    What a ingrate

×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Wash cycle are running to long

FIXED Maytag Neptune, Timer Problem - ApplianceBlog

www.applianceblog.com/.../23387-Maytag-Neptune-Timer-Problem

Mar 4, 2011 - 8 posts - ‎3 authors
My countdown timer is stuck at the 33-minute level in the "wash cycle", and repeatedlyruns for a 30-40 seconds, then stops, then runs, then ... Maytag Neptune TL Washing Machine stops in spin cycle ...
10 posts
Jul 25, 2013
Maytag Neptune Washer Won't Spin/drain
7 posts
Jul 4, 2013
Neptune TL Washer FAV6800AWW - DC and UC ...
5 posts
Jul 3, 2007
MAYTAG NEPTUNE WASHER CONTROL PANEL ...
8 posts
Jun 29, 2005
More results from www.applianceblog.com

Troubleshooting a Too-Long Wash Cycle - whirlpool washingmachine ...

ask.metafilter.com/233920/Troubleshooting-a-TooLong-Wash-Cycle
Jan 25, 2013 - We have a Whirlpool Duet washing machine (about 2 years old). Thecycle is taking WAY too long to complete. The load that's running now ...

Maytag Neptune washer repair: motor/motor control circuit ...

? 12:10
https://www.youtube.com/watch?v=ITTbDh8CFEU
Dec 11, 2013 - Uploaded by daytonaturbofreak
Maytag Neptune washer motor/motor control circuit board ... my board just fried - is your washer still working? wondering how longthe conversion fix will last. ... Other times it will run a completecycle without any malfunctions.
0helpful
1answer

Eratic, sometimes door lock doesnt activate, when it does wahser starts but stop mid cycle and wont continue. Replaced door switch and pump

Repair needed on Maytag Neptune washer - Home Improvement ...

www.dslreports.com > ... > Home Improvement

DSLReports
Aug 5, 2007 - 19 posts - ‎8 authors
Forum discussion: We have a Maytag Neptune front-loader washing machine that ...the drain/spin cycle after a wash even though the timer continues to ... related circuit board failure" their Neptune washer will lock the door, turn on the ... then will either not start tumbling or will stop operation mid-spin cycle.

How To Fix A Washing Machine That Is Not Spinning or ...

removeandreplace.com/.../washing-machine-or-washer-dryer-is-not-spin...
May 13, 2013 - The absolute first thing to do to your washing machine that will notspin or drain (whether it. ... I was so fed up with the machine sometimes refusing to spin or drain the .... I just did a load and it stopped midcycle with e and f error codes.... I tried different cycles but all that happens is the door lock engages ...

Maytag Washer Troubleshooting - YouTube



0helpful
1answer

I have a maytag front loader 4000 series and the control lock light keeps flashing and wont go off..

press and hold the lock button down for 3 seconds and it should unlock. if it does't then the electronic control is malfunctioning.
0helpful
1answer

My maytag neptune TL when it gets down to 12 minutes left it starts flashing dc and wont finish the cycle, what is wrong?

You could have a Clutch malfunction if the machine is a FAV6800A or FAV9800A. If that is you r machine type see this post. Clutch Fix

Post back of you have questions.....Rich
0helpful
2answers

Won't spin or drain, have tried to rerun cycle and checked drain hose

Check pump / outlet filter , refer to instruction book , clean and replace then re- try
0helpful
1answer

Error code of "dc" on my TL Maytag Neptune

If your machine is FAV6800AW or FAV9800AW the dc/UC errors are caused by a clutch malfunction. Your machine is shutting down with those errors so your Tub Displacement Sensor is working as designed.

Fix the Clutch malfunction and you can wash a single sock or a load of blue jeans and you will not take the dc or UC unbalance errors. See this post for the fix.

Post back if you have questions or need help.


Rich


0helpful
1answer

Maytag Neptune TL Washer

if this worked fine before, then I am only guessing that the water inlet valve has malfunctioned. try filling the machine with a garden hose...any change? if still no go, then be sure to have a shop-vac handy to remove the water you just added.
0helpful
1answer

My Maytag Neptune 7500 front load washer will not turn on when the AC or heat is running

Check voltages at the outlet. My guess is that you are on the HVAC circuit, and the Neptune is more sensitive than your hvac equipment. Also check that the neutral is about the same potential as the ground.
Not finding what you are looking for?

861 views

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Brad Brown

Level 3 Expert

19187 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...