Motor controller error - Life Fitness 93ti Treadmill

The meaning of error code F6 can vary depending on the brand and model of the washing machine. Here are some possible explanations for F6 error codes on different brands:

• Whirlpool: F6 error code on Whirlpool washing machines typically indicates a problem with the motor drive tachometer, which measures the motor's speed. This can be caused by faulty wiring or a failed motor control board.
• Kenmore: On Kenmore washing machines, F6 error code can indicate a problem with the motor or motor control board. This can cause the washing machine to not spin or agitate properly.
• Maytag: F6 error code on Maytag washing machines can be caused by a problem with the communication between the central control unit and the motor control board. This can cause the washing machine to not start or complete a cycle.
• LG: On LG washing machines, F6 error code can indicate a problem with the motor or motor control board, or a communication error between the main control board and the motor control board.

It's important to consult the user manual or contact the manufacturer for more specific information and troubleshooting steps based on your specific model and error code.

there's no error code like that
http://www.unitedtechsonline.citymax.com/page/page/4653767.htm

101: EXPOSURE LAMP PROBLEM

120:SCANNER HOME PROBLEM

121:SCANNER HOME

124:SCANNER MOTOR PROBLEM

125:SCANNER MOTOR PROBLEM

126:SCANNER MOTOR PROBLEM

127:SCANNER MOTOR PROBLEM

129:SCANNER MOTOR PROBLEM

130:SICU / SBU PROBLEMS

300:CHARGE CORONA PROBLEMS

301:CHARGE CORONA PROBLEM

303:CHARGE GRID PROBLEM

304:CHARGE GRID PROBLEM

305:CHARGER UNIT WIRE CLEANER PROBLEM

306:CHARGER UNIT WIRE CLEANER PROBLEM

310-316:DRUM POTENTIAL SENSOR ERROR ISSUES

321:LASER UNIT WRITE PROBLEM

322:LASER UNIT 1 SYNCH. PROBLEM

323:LASER UNIT DRIVE PROBLEM

335-338:POLYGON MOTOR PROBLEMS

340-342:TONER DENSITY SENSOR ERROR ISSUES

345:DEVELOPER BIAS PROBLEM

350-355:IMAGE DENSITY SENSOR PROBLEMS

360:HARD DISK 1 PROBLEM

361:HARD DISK 2 PROBLEM

362:HARD DISK 1 PROBLEM

363:HARD DISK 2 PROBLEM

364:HARD DISK 1 PROBLEM

365:HARD DISK 2 PROBLEM

366:HARD DISK 1 PROBLEM

367:HARD DISK 2 PROBLEM

370-375:IMAGE COMPRESSION ERROR

376-377: SICU,IMAGE COMPRESSION ERROR

380-383:IMAGE DATA TRANSFER PROBLEM(SICU, SBU,PRINT CONTROLLER)

384-385:IMAGE DATA TRANSFER PROBLEM WHEN TANDEM IS USED(SBU,INTERFACE

BOARD,SICU,PRINT CONTROLLER)

390:TANDEM IMAGE DATA TRANSFER ERROR(NOISE,SICU,INTERFACE BOARD)

391-392:IMAGE STORAGE ADDRESS ERROR(SICU391-01)

395:CD-R/RW ERROR, INTERFACE BOARD ISSUES

397:CD ACCESS ERROR

398:CD-R/RW DATA ERROR

400:TRANSFER BIAS ROLLER ISSUES

401:TRANSFER ROLLER

430:QUENCHING LAMP ERROR

440:DRUM MOTOR LOCKED

441:DEVELOPER MOTOT LOCKED

491:LASER COOLING FAN LOCKED

495:TONER BOTTLE PROBLEM

496:TONER COLLECTOR BOTTLE PROBLEM

501:LIFT PROBLEMS FOR TRAY 1

502:LIFT PROBLEMS FOR TRAY 2

503:LIFT PROBLEMS FOR TRAY 3

504:LCT 1ST TRAY PICKUP OR LIFT PROBLEM

505:LCT 2ND TRAY PICKUP OR LIFT PROBLEM

506:LCT 3RD TRAY PICKUP OR LIFT PROBLEM

510:PAPER FEED MOTOR PROBLEMS

511:LCT MOTOR PROBLEM

515:TANDEM REAR FENCE MOTOR PROBLEM

520-521:DUPLEX JUGGER MOTOR PROBLEMS

531:FUSING DUPLEX MOTOR LOCKED

532:RELAY MOTOR LOCK

541:OPEN FUSER THERMISTOR

542:LOW FUSER TEMPERATURE

543:HIGH FUSER TEMPERATURE

544:HIGH FUSER TEMPERATURE

545:HIGH FUSER TEMPERATURE

546:LOW FUSER TEMPERATURE

547:ZERO CROSS PROBLEM

550:WEB EXPIRED

591:TONER SUPPLY MOTOR PROBLEMS

592:TONER BANK MOTOR PROBLEMS

601:SBICU TO SBU COMMUNICATION PROBLEMS

602:SBICU TO HARD DISK DRIVE BOARD COMMUNICATION PROBLEMS

620-622:SBICU TO ADF COMMUNICATION PROBLEMS

625-626:BCU TO FINISHER COMMUNICATION PROBLEMS

630:LINE ADOPTER TO CSS CENTER COMMUNICATION PROBLEMS

640-645:BCH TO SICU COMMUNICATION PROBLEMS

646:SICU PROBLEM

650-653:COUNTER ERROR JAPAN

701:ADF P/U ROLLER PROBLEMS

702:ADF FEED MOTOR PROBLEM

703:ADF TRANSPORT BELT MOTOR PROBLEM

704:ADF EXIT MOTOR PROBLEM

705:ADF ORIGINAL TABLE LIFT ISSUES

720:FINISHER LOWER TRANSPORT MOTOR ISSUES

722:FINISHER JOGGER MOTOR ISSUES

724:FINISHER STAPLER HAMMER PROBLEMS

725:FINISHER STACK EXIT MOTOR PROBLEMS

726:FINISHER SHIFT MOTOR PROBLEMS

727:FINISHER STAPLER ROTATION PROBLEMS

729:FINISHER PUNCH MOTOR PROBLEMS

730:FINISHER STAPLER MOTOR PROBLEMS

735:FINISHER PAPER STACK PLATE MOTOR PROBLEMS

736:FINISHER EXIT GUIDE MOTOR PROBLEMS

737:FINISHER FULL STAPLER HOPPER

738:FINISHER SHIFT TRAY LIFT MOTOR PROBLEMS

739:FINISHER FOLDER PLATE MOTOR ERROR

740:FINISHER FRONT SADDLE STITCH STAPLER MOTOR PROBLEMS

741:FINISHER REAR SADDLE STITCH STAPLER MOTOR PROBLEMS

742:FINISHER JOGGER SIDE FENCE MOTOR

750:COVER INTERPOSER BOTTOM PLATE MOTOR PROBLEMS

800:VIDEO OUT TRANSFER,CONTROLLER BOARD

804:VIDEO OUT TRANSFER,CONTROLLER BOARD

818:OPTIONAL BOARD,CONTROLLER BOARD, SYSTEM PROGRAM

819:BAD SOFTWARE

820:CONTROLLER BOARD OR SOFTWARE

821:CONTROLLER BOARD

822:HDD PROBLEM

823:NIB, CONTROLLER BOARD

824:CONTROLLER BOARD, NVRAM

825:NVRAM ERROR

826:NVRAM

827:CONTROLLER BOARD, RAM

828:SOFTWARE,ROM,CONTROLLER

829:RAM, CONTROLLER

835:CONTROLLER,CENTRONIC LOOPBACK CONNECTOR

836-837:FONT DEVICE

838:CONTROLLER BOARD

850:IP ADDRESS,CONTROLLER BOARD,NIB

851:1394 I/F CONNECTIONB,I/F INTERFACE,CONTROLLER BOARD

860-861:HDD

862:HDD BAD SECTORS

863:HDD

864:DATA TRANSFER ISSUES

865:HDD

900:NVRAM PROBLEM.ELECTRICAL COPY COUNTER

901:MECHANICAL COUNTER ISSUES

921:IMB, BICU FAILING

922:IMB, BICU FAILING

924:DRAM,BICU,IMB FAILING

925:BICU, IMB FAILING

926:BICU, IMB FAILING

951:F-GATE SIGNAL ERROR PROBLEMS

953:SCANNER IMAGE SETTING ERROR ISSUES

954:PRINTER IMAGE SETTING ERROR ISSUES

955:MEMORY SETTING ERROR ISSUES

964:PRINTER READY ERROR ISSUES

966:POLYGON MOTOR PROBLEM

970:SCANNER READY ERROR

980:HDD ACCESS ERROR

981:BICU, NVRAM

982:HDD CONSTRUCTION ERROR

984-987:HDD DATA TRANSFER ERROR

990:SOFTWARE PERFORMANCE ERROR

991:REBOOT SOFTWARE ERROR

997-998:DIMM, RAM ERROR

999:PROGRAM DOWNLOAD ERRORS

here are what the numbers mean. 5 is probably throwing the others but you'll need a service tech to know for sure.
have you unplugged/cut off power to it for 10 min to see if it may possibly reset? Worth a try anyway.


Error 1 Door safety lock error

• Check door is closed and latched correctly
• Check wiring
• Check door lock
• Check drum braking device if fitted

Error 2 Not filled in preset time allowed - washing machine does not fill

• Check mains water pressure
• Check inlet hoses for kinks
• Check inlet filter
• Check water inlet valve
• Pressure switch fault
• Wiring fault

Error 3 Not drained in time allowed - washing machine fails to drain water

• Check that filter is not blocked or obstructed
• Check drain hose is clear of any blockage or obstruction
• Check wiring to drain pump
• Check drain pump is not defective
• Check level sensor or switch
• Check wiring to level sensor

Error 4 Multiple instances of anti-flood contacts in pressure switch being made

• Check for overfoaming evidence - can trip pressure switch
• Check wiring to level sensor
• Check pressure switch is not defective
• Water inlet valve locked open

Error 5 NTC fault - temperature sensor detected as either open circuit or shorted

• Check wiring to temperature sensor
• Check thermistor

Error 6 EEPROM failure - defective electronic controller

• Check wiring
• Check electronic control PCB

Error 7 Motor fault detected

• Check motor connector block
• Check wiring
• Check motor carbon brushes
• Check tacho connections
• Check motor

Error 8 Motor tacho fault - washing machine motor tacho detected as open circuit or shorted

• Check motor connector block
• Check wiring
• Check tacho connections
• Check motor

Error 9 Short circuit motor triac on electronic module

• Check wiring
• Check electronic controller

Error 12 Communication error between electronic control boards and wiring

• Check wiring and harness between control boards
• Check electronic control modules

Error 13 Communication error between boards and wiring

• Check wiring and harness between control boards
• Check electronic control modules

Error 14 Water heating error detected

• Check wiring to wash heater and thermostats
• Check wash heater for continuity
• Check NTC (temperature sensor) probe

Error 15 Defective control module - Not programmed Cuore control

• Reprogram electronic controller
• Replace electronic controller

Error 16 Water heating element detected as short circuit

• Check for defective electrical insulation
• Check water heating element
• Check water heater wiring

Error 17 Wrong signal from motor tachometric generator

• Check motor connector block
• Check wiring
• Check tacho connections
• Check motor

Error 18 Defective control module - also can be wrong electrical input frequency

• Check wiring to electronic controller or both if two used
• Check electrical input frequency
• Check mains electrical supply

- Motor control module fault:
Fisher and Paykel washing machine error 1:
Primary Source: Motor control module.
Action: Replace motor control module.

3 - Motor control module fault:
Fisher and Paykel washing machine error 3:
Primary Source: Motor control module.
Action: Replace motor control module.

9 - Size setting fault:
Fisher and Paykel washing machine error 9:
Primary Source: Motor control module.
Action: Reset machine size as per service manual instructions. If fault repeats replace Motor control module.

10 - Temperature Sensor (Thermistor) Error:
Fisher and Paykel washing machine error 10:
Primary Source: Thermistor.
Action: Replace Thermistor.

11 - Pressure Sensor Fault:
Fisher and Paykel washing machine error 11:
Primary Source: Pressure Tube.
Action: 1 - Empty all water from the machine. Remove pressure tube from pressure sensor, clear pressure tube of any water and reconnect tube (blow down the tube is necessary). 2 - If fault repeats, replace Motor Control Module.

12 - Flood Protection Error:
Fisher and Paykel washing machine error 12:
Primary Source: Water Valves.
Action: If the water valves are on continuously, check that the water valves turn off mechanically by disconnecting power to the machine.
Secondary Source: Pump System.
Action: Check pump for blockage and drain hose for correct height(end not immersed in water) or kinked.
Tertiary Source: motor control module.
Action: If water valves are been driven on electrically, replace motor control module.

36 - Water Leak Fault:
Fisher and Paykel washing machine error 36:
Motor control module has needed to top up the water level more than 4 times during wash/rinse cycle. Most likely cause is waster siphoning out or the machine has developed a leak.
Primary Source: Drainage system.
Action: Check that the hose is not less than 850mm from the ground
Secondary Source: Pressure tube.
Action: Make sure the pressure tube is fitted correctly and doesnt have any holes.

37 - Blocked pump:
Fisher and Paykel washing machine error 37:
Primary Source: Drain System.
Action:
1. Check that the drain hose has not been kinked.
2. Check the length of the hose. 1m is maximum extension.
3. Check drain pump winding for open circuit.(Note: Pumps are fitted with a thermal cut out and will reset after cooling)
4. Check for physical blockage to pump and hoses.

38 - Pressure Sensor Fault(empty reading during wash cycle):
Fisher and Paykel washing machine error 38:
Primary Source: Pressure tube.
Action: Check if tube is fitted correctly, check for blockages or holes in the pressure tube.
Secondary Source: Motor Control Module
Action: Replace the module.

39 - Pressure Tube Fault:
Fisher and Paykel washing machine error 39:
Same as fault 38.

40 - Bowl Dis-engage Fault:
Fisher and Paykel washing machine error 40:
Primary Source: Mechanical.
Action:
1. Check that there are no clothes or other foreign objects preventing the clutch from re-engaging. Excessive suds can also stop the bowl rotating.
2. Check the clutch splines for physical damage.
3. Check that the pressure tube has not come off, kinked or blocked(blow down the tube.
Secondary Source: Motor Control Board.
Action: Change Board.

43 - Out Of Balance Switch Fault:
Fisher and Paykel washing machine error 43:
Motor control module has found that signal returning from the out of balance switch indicates that the switch is permanently on or the harness to it is disconnected.
Action:
1. Check the level of the machine.
2. Check wiring to the switch.
3. Check switch for continuity and corrosion.

44 - Water in Bowl During Spin:
Fisher and Paykel washing machine error 44:
Primary Source: Drain system.
Action: Check for blockages/kinks in drain hose and function of the drain pump.

48 - Hot and Cold Inlet Valve Incorrect Signal:
Fisher and Paykel washing machine error 48:
Primary Source: Wiring.
Action: Check the wiring.
Secondary Source: Inlet Valves.
Action: Check the resistance of the coils.
Tertiary Source: Motor Control Module.
Action: Change Module.

49 - Cold Water Inlet Valve Faulty:
Fisher and Paykel washing machine error 49:
Action: See fault 48.

50 - Hot Water Inlet Valve Faulty:
Fisher and Paykel washing machine error 50:
Action: See fault 48.

51 - Diverter Valve Fault:
Fisher and Paykel washing machine error 51:
Primary Source: Blocked diverter valve.
Action: Check for foreign objects in the valve.
Secondary Source: Motor Control Module & Diverter Valve
Action: Plug the machine into the power point but off at the control panel. Check voltage on the plugs at the diverter valve. If voltage around 230V, change diverter valve and motor control module

E000 the heater fails to heat

E001 there is an abnormal rise in temperature

E002 there is an error in the rise in temperature

E003 there is an error in the rise in temperature

E004 there is an error in the IH power supply/IH control mechanism

E005 there is no fixing web/there is an error in the detection of web solenoid connection

E010 there is a feed motor error

E012 there is a drum motor error

E013 the waste toner pipe is clogged

E014 there is a fixing motor error

E020 there is no toner in the developing assembly; there is an error in the detection of

developing assembly toner sensor connection; there is an error in the detection of

developing hopper toner sensor connection

E025 there is an error in the detection of toner feed motor over-current, there is an error in the

detection of toner bottle motor over-current, there is an error in the detection of toner

bottle motor connection

E032 the counter of the NE controller has malfunctioned

E061 there is a potential control error/there is an APC error

E100 there is a BD error

E110 there is a polygon motor error

E121 there is a controller cooling error

E196 the EEPROM is faulty

E202 there is an HP error

E225 there is an error in the intensity of light

E227 there is an error in the power supply (24 V)

E240 there is an error in the communication between the main controller PCB and the DC
controller PCB

As far as I know F28 error code means - SERIAL COMMUNICATIONS ERROR/MOTOR CONTROL UNIT ERROR. Caused by either a communications problem between the Central Control Unit and Motor Control Unit, or Motor Control Unit internal failure.

Error 64,65,66 are related to the same problem
64. (01000000) Phase 5 and 6 - Pressure Transducer (Ptx) error frequency < 66kHz
The Motor Controller module has received signals from the water level sensor (Ptx)
below normal frequency values.
Primary Source: Motor controller module.
Action: Replace Motor Controller module.
65. (01000001) Phase 5 and 6 - Pressure Transducer (Ptx) error frequency > 90kHz
The Motor Controller module has received signals from the water level sensor (Ptx)
above normal frequency values.
Primary Source: Motor Controller module.
Action:Replace Motor Controller module.
66. (01000001) Pressure Transducer Error [Ptx
Frequency > 90 kHz

I have error message E000537-0000 on the screen.

CE means communications error

If there is any breakdown in communication between the machine controller and the motor controller, "CE" flashes and the unit beeps once.
Some common causes of "CE" errors include:
·Conformal coating on serial communications pins between the machine controller and motor controller. After disconnecting power to the unit, try scraping this coating off the pins.
· Check the resistance values between the serial communications pins with the connectors in place. Make sure the harness does not have a bad connection.
· Check the quick disconnect at the motor terminal. The drive motor must be hooked up properly or a "CE" error will occur.
· Drive motor thermal protector has opened.
·Motor controller is not powered or fuse has opened. Replace motor controller.

Press STOP/CANCEL to clear the display.