Question about Jura Capresso Impressa E75 Espresso & Coffee Maker

Open Question

Jura Impreza F50 Open Tap Problem - Jura Capresso Impressa E75 Espresso & Coffee Maker

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
atgep
  • 1 Answer

SOURCE: jura capresso

If you gind too fine, it will overload the pump and result in the "open tap" a few seconds into brew. Rinse and gind coarser to clear out malfunction.

Posted on Jan 20, 2008

Ad
  • 2 Answers

SOURCE: Jura Impressa E fails to dispense, then gives "open tap" message

I had the same problem, when I called their very helpful customer service, I was given these directions.
Take out the tray.
Inside the machine you can now see a flap hanging from the top.
Reach behind the flap, and you should feel a round object/filter. It has a little dimple sticking out in the middle.
Wipe the filter with a paper towel.
Put the machine back together, and voila you got your coffee brewing again.

Posted on Jul 07, 2009

  • 60 Answers

SOURCE: open tap - filling system - close tap

Try using warm water in the watertank, important that the water is not too hot, it can cause leakage in the o-rings in the fluidsytem.
Repeat the procedure a few times, if nothing helps, turn off the machine and wait 1 hour and try again.

If you can`t get around this message, then the flowmeter needs to be changed.

Posted on Jul 12, 2009

  • 3 Answers

SOURCE: Jura Impressa F50 - tray - fault 8

Hi, if you havn't already solved this one, it has been caused by pulling the drip tray/ dump box out while the brew unit was still active. Switch off the machine and insert the drip tray without the dump box. Turn the machine back on and the brew unit should re align itself.

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jura f50 repairing


Probably just needs to be cleaned inside.
This is good video for most models. Parts Guru can do it for you if you don't think you're up to it. Or rebuild the brew group for you.
https://www.youtube.com/watch?v=mZwkqPeZ0QY

Jul 29, 2014 | Jura Impressa F50 Classic Automatic Coffee...

1 Answer

I have the Jura Impressa F50, the machine will no longer function when the coffee grounds conatiner is in place. I have reset the machine several times, have put the container inr\ different positions and...


on the tip of the tray there are metal contacts that tell the machine that the tray is installed. try cleaning these contacts with steel wool and on the inside of the tray with soapy water and a brush. remove excess water from tray and try

Apr 14, 2014 | Jura Impressa F50 Classic Automatic Coffee...

1 Answer

Jura Impressa F50 - tray - fault 8


Hi, if you havn't already solved this one, it has been caused by pulling the drip tray/ dump box out while the brew unit was still active. Switch off the machine and insert the drip tray without the dump box. Turn the machine back on and the brew unit should re align itself.

Feb 15, 2010 | Jura Capresso Impressa F9 Espresso Machine

2 Answers

When turned on it will prompt "Open Tap" "Close Tab"


There are two possible causes. One is easy the other is hard. So try the easy one first. Remove the grinds tray completely, and place you hand in the cavity that it normally takes up. moving you hand slowly in, feel towards the top. you will find a little flap, past that flap there is the tamper and coffee filter at a slight angle. This may be blocked, so clean with a cloth.
If that does not solve the problem (and 90% of the time it does) then you may have a small spec of dust that is stuck in the water system, this needs to be flushed and cleaned. The best place to do that is with a Jura approved center. Unless you are technically minded. Your local Jura chaps sound like they need a k!$k up their behind

Sep 10, 2009 | Jura Capresso Impressa F7 Espresso Machine

2 Answers

Jura capresso


If you gind too fine, it will overload the pump and result in the "open tap" a few seconds into brew. Rinse and gind coarser to clear out malfunction.

Nov 17, 2007 | Jura Capresso Impressa E8 Espresso/Coffee...

Not finding what you are looking for?
Jura Capresso Impressa E75 Espresso & Coffee Maker Logo

Related Topics:

617 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jura Capresso Coffee Makers & Espresso Machines Experts

The Knight
The Knight

Level 3 Expert

76046 Answers

markybean

Level 1 Expert

40 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Jura Capresso Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...