Lan Card Icon not showing in Taskbar

First power off the D-Link for 15 secs, reconnect the power and then reboot your computer. If your computer cannot connect to the D-Link and the Internet then -
I suggest you reset the D-Link back to the defaults and configure it again.

Press and hold the RESET button at the back of the routerwith the power ON until the LEDs flash at the time the release the RESETbutton.
Connect a LAN cable from the D-Link to your laptop/computer's LAN port, openthe browser on your laptop/computer and enter the D-Link's configuration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter) You can now change the default password.
You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.
To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

u might have to update the driver. make sure its plugged in and run windows update and you should be all set and ready to go !
hope this helped plz rate thx

Hi there,
You can install and configure the wireless lan very easily, First of all you require to download the driver for your Acer Travelmate 2410 by below mentioned link
Wireless LAN Driver (Approx 12 MB)

when you download the driver simply right click and extract to the folder, now run the setup and it will install the wlan Drivers automatically, when the drivers are installed reboot the system once so they will run properly, now you will notice one new wireless icon in taskbar along with clock , simply click on the icon and it will show you all the available wireless networks in your area, click to choose your desired network (might require passkey if its secure) and you will be able to access internet/network with wireless connectivity
feel free to contact us if you require more assistance, Regards, Bilal

When you look at the Manage Network Connections link on the Network and Sharing Center you do not see
Local Area Connection?
Do you see Wireless Network connection?
You need to check the device manager to see if the card has been disabled.

It should show two entries with no red or yellow marks. One for wireless (WLAN) and one for wired (Ethernet)

Hi,

You can enable it again, just goto control panel, open network connection, there will be local area connection icon, Right click on it and click on enable.....

If there is problem again use motherboard cd and install lan card drive again...

while reformating the lan drivers and other related drivers are being wiped out. so load your lan driver software again. if you find it hard to get 1, then goto www.hp.com and refer your model, then get all drivers from the site. to be more sure if your drivers are not installed,go on device manger, and check the question mark(?) with yellow colour, all those are not installed..load it

yes its plug & play device, actually your system can detect such device like your new LAN card. The device is still on your Device Manager but not totally working, need to install first its software to run that new LAN Card.
If you don't what kind of your new LAN card, just install a program that identify the name & model of your LAN card device. Here is the link to install that freeware software www.astra32.com run this program to diagnose the system and identify of your new LAN card device. Good luck!

If you are using a windows XP as an OS...make you have loaded all your drivers inclucing the LAN. Secondly from the START go the control panel--network and internet connections--network connections--you'll see the LAN icon/s.Right click on it and select Enable/Disable.

hi gangesh click on the start button......connect to.....go to all connections......the choose your lan connection right click and go to properties........then make sure the bottom two boxes are checked...the one that says show icon in the notification are when connected......and the one that says notify me when me i have limited connectition.

this will give the icons in the tasbar.....
now if you want to put in a manual ip address ect...then in that properties page click on tcp/ip then click the properties button....
there put in your ip and subnet mask and gateway and dns.
hope that helps.

Goto control panel and work your way through the network Set-up Wizard.
If this is not a separte Icon in control panel then look under "network Connection" Icon.