Gaggenau GI936-760 Dishwasher Logo

Related Topics:

Frank McMahon Posted on Aug 02, 2007

Gaggenau GI 936-760 dishwasher

Dishwasher makes a slight, continuous grinding noise...just started. 5 year old model It runs for a few minutes and then an "F" shows up in the 'minutes remaining' panel. Any ideas would be appreciated.

1 Answer

A

Anonymous

Buy a new one and sell me the door. I have been looking for this model's door for a long time!
[email protected]

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
1answer

Dishwasher is making a loud noise

Sounds like there is something in the filter trap that is right before the mini disposal that is a fan blade, on top of the motor.
0helpful
1answer

We recently purchased a new pump for our frigidaire gld4355rf dishwasher. The old one started making grinding noises. When we moved the dishwasher it had leaked due to a failure of an interior seal. Our...

it could be a crinkle in the drain pipe or slight block, the pumps do make some sounds from time to time. it some time can even be the rubber grommets were the pump sits.
0helpful
1answer

When washer is started make loud grinding noise

Very likely the bearings in the motor have begun to fail. You can replace the motor, but for a 15 year old DW, sometimes it makes better sense to just buy a new one. Depends on the features the old DW has, vs new, vs motor replacement cost.

Reply back and we can you more.
Dec 13, 2009 • Dishwashers
6helpful
1answer

Kenmore Ultrawash Quiet Guard 5 making buzzing/grinding noise

I have a very similar dishwasher, with a very similar problem. I fixed it by removing debris from the water evacuator pump located towards the front of the bottom of the machine (the last motor before the drain hose. In my case, grape stems had clogged it up. Once emptied, it purrs once again. NOTE: don't disassemble the motor, just flush it out, there is an o-ring gasket that is a bear to re-install.
0helpful
1answer

Template for GI 936-760 wood panel

My husband ended up measuring and drawing his own template.
0helpful
1answer

Bosch dishwasher timer freezing

There is a recall on the control board of many of these models, butyour problem is likely not related. It sounds like a plugged drain system or a possible bad drain pump. That's why you are hearing the pump running constantly. I have written a guide to help. It is here. Thanks!
5helpful
1answer

Kenmore elite dishwasher noise

I had the same problem where rubber gasket that seals the motor bearings leaked water into the bearing and rusted out the bearing.

I scrapped the motor into every little pieces and extracted the bearing and just replace it. Now it is quiet as a mouse.

You need a bearing puller to get the bearing out for about $20 and the bearing is $6.
During the repair i slightly bent the shaft and i didn't straightened it properly so it wobbles a bit. But it works and if really quiet.
May 13, 2008 • Dishwashers
0helpful
1answer

Kenmore dishwasher

Mine eventually "fixed itself". I think some debris got caught and eventually (5 cycles or so) got ground up and sent through the drain. The noise changed each time it got closer "flushing out"
Not finding what you are looking for?

446 views

Ask a Question

Usually answered in minutes!

Top Gaggenau Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

Brad Brown

Level 3 Expert

19187 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Are you a Gaggenau Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...