Turntable wont stop turning, even when not in use

Bad Door switch, back feeding power to turn table motor circuit

There is no turntable control. It is always on. The turntable should change direction each time the unit is used. If the turntable is not operating, it has malfunctioned. Newer microwaves for the most part all have full-time turntables to promote even heating, thus reducing customer complaints about ovens that don't heat right.

Good Afternoon Friend, I appreciate your post!

If the turntable of your Frigidaire microwave has stop working, often the possibilities include one of three culprits:

• Power Supply
• Turntable Turned Off
• Turntable Support Damaged

I always recommend resetting your microwave first before reaching out to a professional. You can do so by unplugging your appliance or flipping the circuit breaker for about ten minutes and then turn on your microwave.

Best of luck!-Z

Most likely you have a shorted fan/light relay on the control circuit board.

HELLO.

The turntable is the unit in the center of a microwave that you set your food on. It rotates during the microwave cycle, making sure all parts of a dish are properly heated. These are typically made of either hard glass or microwave-safe plastic.

Your microwave turntable may not turn due to any of these problems explained below.



(a)If your turntable is removable (as many are for cleaning purposes), it may have come loose from this turning mechanism.place the turntable properly on the turning mechanism.


(b)If your turntable was previously working and now does not any longer, check the settings on your microwave's LCD display to make sure you haven't accidentally turned off the turntable.
Most microwaves have different settings that the user can select with the press of a button, like a "Defrost" setting or a "Popcorn" setting. Certain microwaves may stop the turntable from turning during certain pre-programmed selection modes. Stop your microwave and don't use a pre-programmed mode. Instead, just specify the time using the number pads and start your microwave to see if your turntable begins to rotate again.


(c)The rotating mechanism on the inside of your microwave that rotates the turntable is actually connected to a small motor on the inside of your microwave's case. If this motor burns out or stops working, the mechanism will stop turning. This is something that needs to be replace.

follow these steps below to replace the faulty motor.

1. Open the microwave door, and carefully remove the turntable tray. Also, remove the frame that the turntable is positioned on. Both the turntable and the frame are not secured in the oven, so removing them is a quick process.

2 .Remove the bottom panel of the microwave. The Microwave Wizard website explains that the number of screws securing the panel varies depending on the manufacturer and specific microwave. Once the bottom panel is loosened, disconnect its wiring harness in order to completely remove the panel.

3. Locate the turntable motor. The Microwave Wizard website explains that the motor compartment should be positioned below the center of the microwave. Unscrew the motor, disconnect the wires, and remove it from the microwave.

4. Determine the specific part number for the turntable motor so that a correct replacement can be purchased or ordered. Position the new motor into the shaft in the bottom of the microwave. Screw the motor securely into place.

5. Test the microwave to make sure that the turntable motor is operating correctly. The Microwave Wizard website explains that the motor can make noises if it was not positioned evenly in the shaft. Reconnect all of the wires that were detached when removing the old motor.

6. Reinstall the microwave's bottom panel parts, and secure all of the screws in place. Reposition the turntable frame in the bottom of the microwave and place the turntable on top of it. Test the microwave in order to make sure that everything is working correctly.


Thanks.

your magnetron might be out. its what heats

the noise is the turntalbe trying to catch on the motor below soundslike it worn out

Most of these are belt driven. You need to uncase the unit and check the belt.

Like anything with high voltage, use good safety practices.

It sounds like you have a jamming turntable motor.

The turntable system consists of the motor, the coupler, the turntable support with rollers, and the tray.

You can see and hear a video of how a turntable motor should sound when you rotate it by hand.

If yours won't rotate or it sounds like it's grinding, etc., you may have a bad motor or plastic coupler.

To replace either, you need to unplug power, then remove the bottom cover of the oven.

You can usually find helpful exploded view diagrams and order parts by entering your full model number here.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.