SWA-4000 Sound Interference Problem

The Samsung TX card is used to send part of the audio signal from the main unit to the wireless module that controls the surround sound (rear) speakers for a Samsung Home Theater system. It isn't going to act like a ChromeCast device for your tablet.

The Samsung AH81-04177J (SWA-4000) is only compatible with a small number of Samsung Home Theater systems. see http://www.samsungparts.com/Products/Parts_and_Accessories/PID-AH81-04177J.aspx . One of the supported systems is the Samsung HT-BD3252, https://www.samsung.com/us/support/owners/product/blu-ray-home-theater-ht-bd3252-series . See the manual of the home theater system for more information: http://downloadcenter.samsung.com/content/UM/201104/20110419185210639/HT-BD3252A_XAA_0807[1].pdf .

I hope this helps.

Cindy Wells

start with the main unit turned off. Press and hold the button on the back of the swa-5000 module until the light on front starts blinking fast. Then point the remote at the main unit and press 0-1-3-5-ENTER. The standby light on the main unit should turn off then back on. Turn on the main unit and it should find and link with the wireless amp.

Unfortunately it would appear not. I just bought an SWA 5000 for my HT TZ 225 home threatre system as it would seem the SWA 4000 has been discontinued - the HT-TZ225 refers to the SWA 4000 doesn't it.

The tx card that accompanied the SWA 5000 was too big and did not fit in the back of the DVD player so I will have to return this to the retailer and keep looking for an SWA 4000 . . .

Unless anyone has another solution.

With the home theater system off, press the 0-1-3-5 buttons in that order on the home theater's remote control.

Power on the home theater system.

With the wireless module on, press the [ID SET] button on the back of the wireless module for five seconds.

If your home theater continues to display rear check after you have tried the steps above, call Samsung Customer Care at 1-800-SAMSUNG (1-800-726-7864). Have your model number and serial number on hand to set up service.

Hope this helps!

With the home theater system off, press and hold the REMAIN button on the home theater's remote control for 5 seconds.
Note: You can release the REMAIN button when the POWER LED blinks blue.

With the wireless module turned on, use a ball point pen to press the RESET button on the back of the wireless module. The POWER LED in the front of the home theater blinks two times.

Turn on the home theater. The LINK LED on the front of the SWA-3000 changes from red to blue, indicating the wireless module has connected to the home theater.

If your home theater continues to display rear check after you have tried the steps above, call Samsung Customer Care at 1-800-SAMSUNG (1-800-726-7864). Have your model number and serial number on hand to set up service.

1. Connect the front left, front right, center, and sub woofer speakers to the back of the home theater system.

2. With the home theater system off, insert the TX card into the TX Card connection (WIRELESS) on the back of the home theater.
Important: Make sure to insert the TX card with the slanted portion of the card facing left.

3. Connect the rear left and the rear right speakers to the back of the SWA-3000.

4. Plug the power cord of the SWA-3000 into an electrical wall outlet, and then switch the power switch on the back of the SWA-3000 to [ON]

Hope this helps!

You have to reset the connection:

With the home theater system off, press the 0-1-3-5 buttons in that order on the home theater's remote control.

Power on the home theater system.

With the wireless module on, press the [ID SET] button on the back of the wireless module for five seconds.

If your home theater continues to display rear check after you have tried the steps above, call Samsung Customer Care at 1-800-SAMSUNG (1-800-726-7864). Have your model number and serial number on hand to set up service.

Hope this helps!

swa-4000 wireless module isn't compatible with htz310. You need to buy Samsung's swa-3000 to work with your htz310. I had the same problem. It tells you in your owners manual under conectivity where it explains about hooking up a wireless module(pg.55-60). I hope this helps.

Google "Samsung SWA-4000" The HTz310 is wireless "ready" only. You'll need to purchase this unit for about $100 to make your (Rears only) wireless.

I have had the same problem with the wireless unit and thought the same, it didn't work. The way to fix this is simple. You need to do the 0, 1, 3, 5 on the remote and turn on the home theatre system on the main switch on the front panel (as I was doing this on the remote, and it was failing). The blue light should then stay illuminated. If not just switch the main on/off button again, and it shoud work.