Question about Maytag Ensignia 3.3 cu. ft. Top Load Washer

Open Question

Maytag Ensignia will not rotate during the wash cycle

My Maytag Ensignia Washer will spin and drain during the spin cycle but makes an awful racket and will not spin during the wash cycle. Any help is greatly appreciated.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Jimster
  • 240 Answers

SOURCE: Leak from maytag top load coin machine during spin drain cycle only

Possible that you would have a tub seal leak if it is only noticable during spin cycle. Possible that it "drips" slightly while in agitation, but not enough to notice it. While in spin mode you have a lot more parts moving as well as a lot more water pressure on the seal itself. Pump could also be leaking, but highly doubtful since it would leak a constant amount at all times. Good Luck!!! Jim

Posted on Sep 09, 2007

Ad
Lumpy816
  • 246 Answers

SOURCE: ensignia maytag washer noise

The bearings on Maytag Ensignia's are part of the seals that keep the water in. Once you start hearing the bearings begining to go, you likely will have a leak following shortly thereafter as the bearing greased is washed out by your laundry soap. Up front. This is a procedure that requires specialty tools and takes me about 45-60 minutes to complete. The easiest way to tackel this job is to take your model number (just on the back side of the console) and take it to a local appliance parts store. Ask them for a tub seal kit. (I can't give you a part number since there is no model number listed) but they should be able to pull it up for you. When they bring it up to the front, inside the seal kit is not only step-by-step directions, but also the part numbers for the specialized tools required as well. If you opt to go the repairman route, I'll forewarn you, the company I worked for charged around 250-300 for the repair on this. Send me back a message if you have any troubles or other questions.

Posted on Jul 01, 2008

  • 1 Answer

SOURCE: My Maytag Neptune washer won't spin during the spin cycle.

I'm having the same problem...Does it say LR?

Posted on Jul 20, 2009

  • 90 Answers

SOURCE: Grinding sound during agitation cycle on my Maytag Performa

Its probably you stator plate and rotor. But you need special tools for this repair. There a spring that is under 200 pounds of pressure and if you take the screws off that hold the plate its going to fly into you face if your dont use the special tools to depress the spring. Is it more of a clanking kinda of noise? DOes it olnly happen with heavy loads? Try this out. Fill the washer with water only. and get it into a wash cycle with water only. If there is no noise then put in like a load of towels. A heavy load. Now if you hear the noise now then its for sure you stator plate and rotor..hope this helps, but like i said you need those special tools to do this repair or injury can result from the spring part.

Posted on Jul 27, 2009

dwrooker
  • 6 Answers

SOURCE: maytag PAV2300AWW Washer makes grinding sound when agitating

Sounds like it is the bearing on the water pump. Take off back plate and replace and remove 3 screws and two hoses (the one hose is a waste line so make sure you have a bucket to empty our waste water) after removing these remove belt on bottom of pump.

Posted on Oct 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag ensignia top load washer will not fill with water at start of the cycle?


The drain hose has to be at least 30 inches above the floor or gravity will drain the machine. Also: If the water hose is jammed into the drain a siphoning affect will occur in some instances.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Aug 04, 2012 | Maytag Ensignia MAV2757AWW Top Load Washer

1 Answer

My Maytag Ensignia is filling with water then stopping. If I manually move it through the cycle it does nothing. Won't spin or drain. There is no noise when it goes to the agitate or spin cycle (as if it...


f the lid switch is defective, your washer can't spin and may not function at all. The switch is inside the washing machine main housing near the door frame. Often you have to raise or open the top or front of the washer to get to the switch. If it's defective, you need to replace it. You will need a putty knife to release the clips located of the front corners of the of the lid. If you look along the seam of the top and the front panel, just near the corners, you will see them. Just push in on the clips and lift the top to access the switch.Here is a link to the part.

Jan 04, 2011 | Maytag Ensignia MAV3757AWW Top Load Washer

1 Answer

Maytag ensignia makes a great deal of noise during rinse cycle


"If you dont have a noisy spin cycle and the noise you hear is only on the rince cycle, dont be worried, as this is totally normal. Water sprays onto the drum while the spin cycle is in progress and rewets the clothes to allow any existing soap to be desolved. This noise is in effect the water hitting the drum during the rince part of the cycle.

Sep 03, 2010 | Maytag Ensignia 3.3 cu. ft. Top Load...

1 Answer

Maytag performa PAV2300AWW does not spin (wash cycle works fine). During the spin cycle the tub does not rotate...but i can hear the motor running...water drains...Pls help


Hi,

Problems with a washing machine not spinning or not draining are often inter related..

If you are having a problem with your top load washer then check out this tip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkout this tip...

Front Load Washing machine not draining and or not spinning


heatman101

Aug 29, 2010 | Maytag PAV2300 Top Load Washer

1 Answer

Spin cycle not working properly


On the transmission there are two shift arms. One shift arm controls the agitator and the other shifts to spin the cloths. If the washer has been making a "clicking" sound when it trys to spin, the solenoid that shifts the spin shift arm is not catching and the drum will not spin. The other possibility is the spin clutch is slipping and make a "grinding/ratcheting" sound. Neither, unfortunately are inexpensive to fix.
If you can describe the sound and when it occurs, I might be able to get closer.
Let me know.
Regards,

May 15, 2009 | Maytag Ensignia MAV4757AWW Top Load Washer

Not finding what you are looking for?
Maytag Ensignia 3.3 cu. ft. Top Load Washer Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...