Power cord for vx-3300

Already answered for DPS-12 in 2011 which suggests a fuse where the power enters, However, your manual mentions no fuse, but 'protection circuitry'. If there is a fuse, it will be inside and on a circuit board. All fuses have the rating on the end cap of glass fuses and on the side of ceramic fuses, which as also colour coded.

https://velodyneacoustics.com/pdf/vx-11/VX-11Manual.pdf

Where to find fuse on velodyne vx-10b - Fixya

www.fixya.com > ... > Velodyne > VX-10 Subwoofer

Sep. 11, 2011 - where to find fuse on velodyne vx-10b - Velodyne VX-10 Subwoofer. ... in the manual shows a fuse rating of 2 amps where the power cord enters the box. ... here's a link to the owner's manual: http://velodyne.com/vx-11.html.

This is a problem that can't be diagnosed over a computer. There could be several reasons that the AM regulator is being blown. The radio needs to be serviced by a Radio Technician.

don't use the amp you are drawing to much power for it and thats why the cord is getting hot.

If it is new take it back and have it checked

• With the switch sitting as it is in the picture below (actual switch recessed tho the right. Soldier the wires in this order.

1. Black
2. Red
3. Lite Blue.
4. Dark Yellow (This yellow wire comes from the mic cord itself)
5. Shield.
6. Lite Yellow. (This yellow wire runs off to the side of the mike to the electrical components inside the mic)

• Standard 4 pin Cobra mic tip to run it to that Connex.

• Pin 1 - Shield.
• Pin 2 - White.
• Pin 3 - Red.
• Pin 4 - Black.

• If you have any comments please feel free to leave them here.
• Hope this helps and thank you for using FixYa.

Regards, Tony

Your Canon copier ir3300 shows front cover open, but actually it is not. It could be the sensor problem, try with this Power off the printer then unplug the printer's power cord, wait 5 seconds then replug the power cord in. Hold the Power button for 6 Beeps and release the Power Button. This will reset the printer and should resolve your problem.

E000 0000
The reading of the main thermistor does not reach 30°C 1 sec after the main
power switch is turned on. Or, it does not reach 70°C 2 sec thereafter.

Main cause:
The fixing film unit is faulty. The main thermistor has an open circuit. The
fixing heater has an open circuit. The main power supply PCB is faulty. The
DC controller PCB is faulty.

Caution:
To reset the error, execute the following in service mode:
COPIER>FUNCTION>CLEAR>ERR.

Action:
1. Connector
Is the connector of the fixing assembly connected?
a. main power supply PCB (J8) <-> relay connector <-> heater
b. DC controller PCB (J320) <-> relay connector <-> thermistor
NO: Connect the connector.

2. Fixing film unit (thermistor)
Check the interval between pin 1 and pin 2 and between pin 3 and pin 4 of
the connectosr (4-pin) of the thermistor for electrical continuity. Is it ¥W
(open)?
YES: The heater has an open circuit, or the thermal switch is open. Replace
the fixing film unit.

4. Main power supply PCB, DC controller PCB.
Press the Start key. Is the drive voltage of the heater supplied by the connector
J8 of the main power supply PCB?
Main heater: between J8-1 (FSR1) and J8-5 (FSR COM)
Sub heater: between J8-3 (FSR2) and J8-5 (FSR COM)
YES: The heater drive power supply is faulty. Replace the main power
supply PCB.
NO: The thermistor control mechanism is faulty. Replace the DC controller
PCB.

May I suggest Live-Tech there staff will located the cord you need and assist in the ordering process.

Thanks Frank
Live-Tech
1-888-361-8511
http://www.mylive-tech.com

just clean the sorter unit section
if sorter not attached blower on heater sections up side on delevary section.

Hi,

Please follow the follwoing steps,

1) unplug the power cord at the both ends from the printer and wall outlet. connect to wall out let directly dont connect to printer.
2)Press and hold # and 6 while reconnecting the power cord to the product hold for 1 min after plugging the power cord, and then release both buttons, this should resolve the issue.

Regards,
raj_p5983