Tech sheet missing need help with codes

Remove the toe-kick panel located under and behind the dishwasher door (2 screws or 2 quick-release catches). Look on the other side of that toe-kick panel. There should be a technical data sheet stored in a little plastic pouch there (if someone hasn't stolen it), which will explain the meanings of the various blink codes. Don't forget to put that tech-data sheet back for the technician, in case you decide that you can't fix it yourself and decide to call a professional!

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

Trcontrol panal sorryy turning off the breaker for thirty seconds if not it could be a stuck

i.have xp-431 diagnostices software.id code-67718702 but missed dev.code and reg. code pl solve my problem immidetlly thanke.

66. (01000010) Phase 6 - Pressure Transducer (Ptx)
Error - Frequency > 90 kHz
Note: this supersedes Fault code 65 from V41 Motor Control Module
code onwards.
The Motor Control Module has received signals from the water level
sensor (Ptx) above normal frequency values.
Primary Source: Motor Control Module.
Action: Replace Motor Control Module.

There is a technical data sheet inside the washer cabinet that should list all the error codes and detailed troubleshooting information. To access, you need to lift the top panel. There should be a screw located under plastic cover plate on each side that you need to remove in order to lift the top panel. Once the panel is lifted, the tech sheet should be sealed in plastic along one of the interior cabinet walls. I hope this helps you.

if the clean light is blinking that mean you dishwasher is having a heater issue. it is an error code. either your control board is bad or the heater or the ntc therm. if you take the bottom panel off you will see or should see a tech sheet that will tell you how to clear the error code or this website will help you. just enter your model number http://servicematters.com/docs/wiring/wiring_main.htm

This information may help in your situation. The following link explains how you may be able to clear the blinking clean light problem:

http://www.fixya.com/support/r417123-blinking_clean_light_kenmore_whirlpool

Now, keep in mind all dishwashers are not alike and have different panel options. If you do not have the same set up that I have mentioned, the tech sheet for your dishwasher will explain the touch pad functions. The tech sheet is located behind the lower toe panel under the door and lists the proper sequence of buttons to push for diagnostics and troubleshooting. Just remove the screws that hold the panel in place and remove.

NOTE: Sometimes the tech sheet is located behind the inner door panel. You will need to remove the screws securing the inner panel to access it if this is the case. Make sure you turn off the main power breaker before doing so.

Often, I have found this to be a momentary glitch in operation. However, if the problem keeps reoccuring the number of flashes is an indication of WHICH circuit is causing your problem. You will need to refer to your tech sheet to determine this.

If you have any questions, please let me know. I hope this helps you solve your problem.

Take off the kick panel on your dishwasher, inside the panel there should be a plastic pocket with a sheet of paper in it called a "tech sheet". This is a basic diagnostic tool for techs. It should tell you what the flashing green light is indicating. Every model is a little different so it's hard to say exactly what it is. The tech sheet will walk you through how to get it out of this mode.

Good luck!

sorry buthtere should be one located under the main console, remove the 2 screws from the back and flip it foward, if not give f&p a calll, they will help you out

take note of whoch lights are flashing on back panel, generally i ask cust to take a index card or similar size paper and placedit under your light indicators(wash--rinse----spin)think thers 7 or so lights .noting which ones are flashing when shuts down, will determine problem for you,under main console(2 screws across back) is a tech sheet to help you out