There are no screws on the speaker grill of this particular model

hi.
if there are no obvious screws on the grille, then it is probably part of the door card.
you would need to remove the door card to acess the speaker.
if it is the grille itself you are trying to replace, then you may have to genty pry ot off and glue the new one back in place.

This is more difficult than it looks because the rear trim panels must be removed in a certain order as they overlap at their edges.

First remove the rear seat.
Remove the step panel from the floor near the side door opening.
Unbolt the 2 seat belt anchors.
Remove the trim panel below the lift gate (rear hatch opening.) Pry the screw plugs out with a small screwdriver and remove the screws.
Pry out the rear speaker grill using a flat blade screwdiver that has been taped to prevent scratches.
Remove the rear speaker mounting screws. Pull the speaker out and unplug the connector.
Remove the passenger side trim panel mounting screws.
Use a panel clip removal tool and pry the clips that hold the trim panel then lift the panel away.

Installation is the reverse of removal.

Try soaking it down with WD-40 and letting it sit for a bit. Usually you can heat up a sticky screw/bolt and get it to break, but since youre next to the gas tank, its not recommended.

I have the exact problem with my LG LHD45EL as lubbock51's Aug 17, 2010 question. (see below) Isn't there anyone out there that's had this same problem and resolved it. I too am afraid to pry the grill for fear of breaking it...it made out of plastic so it won't take much to break the grill if I did.

By lubbock51 on Aug 17, 2010
I have an LG LHD45EL dehumidifier. The manual shows removing the front grille to clean the coil by placing a hand on each side and pulling toward you. Mine won't budge and I'm afraid to pry the plastic in fear of breaking it. Any suggestions?

SPEAKER GRILLE Removal
Pull the SPEAKER-GRILLE away from the cabinet to remove.
SCREEN-ASSY Removal
1) Remove 10 screws (a) from the upper cabinet rear cover (3 screws on each side and 4 screws across the
top).
2) Remove screws (b) along the bottom of the SCREEN-ASSY (8 screws on 52 inch models, and 12 screws
on 62 inch models),
3) Unplug the LL connector to the front CONTROL-PANEL.
4) Lift the SCREEN-ASSY up slightly and then pull away from the cabinet.
CABINET FRONT DISASSEMBLY

please rate, thx

Door Trim Panel Removal and Installation

1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .

1. Remove the door handle cup cover.

1. Remove the screw.

1. Remove the switch plate by lifting the front and moving it forward.
   • Disconnect the electrical connectors.

1. Remove the speaker grille.
   1. Release the front clips.
   1. Move the speaker grille forward.

1. Remove the speaker screws.

1. Remove the screws and the door trim panel.
   • Disconnect the electrical connectors.

1. To install, reverse the removal procedure.

Some speaker manufacturers design their boxes with non-removable front grills. Be thankful that you can remove the back because I've seen these sealed as well. Once inside, the speakers should be mounted from the inside (mounting screws on inside) compared to front mounted. IF they are not then either you're not using the proper method to remove the grill OR it's glued in place and will require breaking the glue bond to release the grill. One note to remember...non-removable grills can mean the manufacturer has something to hide.

There are two screws (1/4 in. philips) located in the lower left and right front of the cabinet near the floor. They may be concealed by a plastic overlay. It can be popped off with a small screwdriver.

Be careful!

michtech

Magnasonic has customer support email [email protected]

Remove grill from speaker that has the snap connector. Remove 4 screws, gently pull out speaker and padding. Put pressure on connector (making sure the connector is out at the max. position)with middle and index finger at the same time placing other speaker onto connector, slightly turning speaker. You will here it snap in. Just use maximum pressure with fingers. Do not use tools. Connector is made of plastic and can break very easy.