Lamp replacement fears

is the lamp bad or or the whole assembly.

but varies by country.
http://www.scantool.net/software/alldata-diy-1-month-subscription.html


generic? the whole deal.
1: gain access to back and remove screws there. (even under fender)
2: on some cars the front nose of car bezel must be removed
gaining true access to lamp housings, and the screws.
disconnect the socket wire (or replace bulb now)
and then the housing screws. bingo its free.
some cars, the hood opens
and there is a plate that extends L/R across front of car.
remove top plate and bingo , lamps.

hi,
do the following steps to change the lamp of your projector.

1. Turn the power off and disconnect the projector from the wall socket.
2. Turn the projector over. Then loosen the screws and remove the lamp cover. If the lamp is hot, avoid burns by waiting for 45 minutes until the lamp has cooled.

3. Move the latch to another end as shown in the picture.


4. Loosen the screw that holds the lamp to the projector. If the screw is not loosened
completely, they could injure your fingers. It is strongly recommended that you use a
magnetic-head screwdriver.

5. Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector.


6. Insert a new lamp. Make sure the handle is fully locked, move the latch back, and
tighten the screw firmly.

7. Re-install the lamp cover and tighten the screw. Do not turn the power on with the lamp cover removed. Whenever the lamp is replaced, reset the total lamp operation time. Do not reset if the lamp is not replaced as this could cause damage.

8. Resetting the lamp counter
i. Press and hold the Exit 5 button on the projector for 5
seconds to display the total used lamp time.
ii. Press Auto on the projector or on the remote control to
reset the lamp hour to "0".
iii. Wait about 5 seconds to let the OSD disappear.

ok

With the TV off, unplugged and having cooled down for at least on hour (you can force it to cool faster see the manual), take off the front cover. Grip it from both sides and pull it away from the TV. Loosen the screw that holds the lamp cover and remove the cover. Next loosen the screw that holds the lamp in place. Pull the lamp out slowly by the handle. Handle the new lamp with a cloth to avoid oils and dirt getting on the lamp. Put in the new lamp making sure to properly align it in the TV. Retighten the lamp screw and then put on the cover and tighten its screw. Replace the front cover. If the screws and lamp cover are not correctly positioned, the TV will not work (a protective circuit is involved).

Next reset the lamp time (instructions should have come with the replacement lamp). Wait until the lamp notice disappears from the TV screen. Press and hold the Vol down button on the TV while pressing the Split/Play button on the remote. Hold both buttons until you see a notice that the lamp time was reset (about 4-5 seconds).

For a download version of your manual, see http://www2.panasonic.com/consumer-electronics/support/Televisions/LCD-Projection-TVs/model.PT-50LC14 .

I hope this helps.

Cindy Wells

You must remove the plastic cover from the front and just left of center there is a panel covering the lamp with a single screw. Under that the lamp is also held in with a single screw. Pull on the handle firmly to remove lamp. Replace with TY-LA1000 bulb.

replace the lamp! the model number for the lamp is...ux21511. On the front of your tv there is a panel that runs from left to righ across the bottom thats 6 to 7 inches tall remove it. once you did this look at the lower left hand side of the unit. there will be a yellow label on the little door or hatch. remove the screw and take off the hatch. after that look at the inside of this it looks like a rectangular box. remove the two screws directly in front of you and carefully remove the lamp. its attached to the cover you just pulled after you removed the screws. reverse these steps to reinstall the new lamp. there you go problem solved!

1. Check that headlamp switch (11654) is in the off position.
   
2. Lift hood (16612).
   
3. Release latch and swing filler panel to left or right.
   
4. Remove electrical connector from headlamp bulb by grasping wires firmly and snapping connector rearward.
   
5. Remove headlamp bulb retainer (13N019) by rotating counterclockwise (when viewed from rear) about one-eighth turn and sliding ring off plastic base. Keep headlamp bulb retainer as it may be used again to retain new headlamp bulb.
   
6. Carefully remove headlamp bulb from socket by gently pulling straight backward out of socket. Do not rotate headlamp bulb during removal.

Headlamp Assembly, Explorer
Removal and Installation

1. Disconnect battery negative cable.
   
2. Remove blind rivets (2) attaching screws (4) and radiator upper sight shield.
   
3. Remove turn/park lamp attaching screws (2) and pull assembly away from body. Remove bulb sockets from housing and remove lamp assembly. Repeat on opposite side of vehicle.
   
4. With turn/park lamp assembly removed, screw attaching grille to front fender flange is accessible. Remove grille attaching screw. Repeat on opposite side of vehicle.
   
5. Remove attaching screws (4) located across top of grille.
   
6. Grip lower edge of grille and pull outward to disengage from retaining clips. Remove grille.
   
7. Using needle-nose pliers, compress barbs on headlamp housing retainer. With barbs compressed, pull forward on housing just enough to disengage from retainer. Repeat on opposite side of headlamp housing.
   
8. Turn headlamp housing as necessary and pull forward to disengage from headlamp aiming ball socket.
   
9. Disconnect wiring from headlamp bulb socket.
   
10. If replacing headlamp housing, remove retaining collar and bulb.
    

For installation, follow removal procedures in reverse order. Make sure to check headlamp aim.

Yes. The lamp is timed and the replacement indicator signals when the lamp is near end of life. If the lamp fails catastrophically it makes a mess... best to replace before that happens.

Yo learn how to replace the lamp go to link below and page 133 will tell you.

http://downloadcenter.samsung.com/content/UM/200509/20050902121438187_BP68-00469A-02Eng_0902.pdf

The lamp is on the bottom left side. Remove the plastic piece that goes across the TV below the screen. It will snap off. No screws. Remove 2 screws to access the lamp carriage.
Make sure you DO NOT touch the new lamp with your bare hands.

Look inside behind the light and see if there is an access cover, if not you will have to remove the tail lamp to replace the bulb. If you open the rear hatch and look at the lamp you should see a couple of screws that hold the lamp to the car. Remove these and pull the light out.