Wirless isn't picking up on device

hi

this printer is wirless WiFi ready -- i assume you installed the drivers (CD came with printer) onto the computer . if so, turn printer on and it will be recognised by the computer via your router (wireless device, attached to your hispeed modem). Printer does not have bluetooth capability

If you mean wireless internet
1 Make sure your router is on
2 Make sure your WIRELESS COMPATIBLE ROUTER is plugged into your modem
3 If so reset it
4 Make sure your wii isn't more that 700 to 800 ft(Its probaly not)
5 Change your security settings to WPA, or TKSP, or TKSP-WPA
6 If that fails, try using a wired connection. Plug one end of an ethernet cable into your wii, the other into a wall jack or IF AVAILABLE A ROUTER OR MODEM
Thank you for your time, good luck and I hope this helps

The Canon is trying to connect to a wireless router or wireless access point which is connected to your computer network. Your Sprint 3g device is a wireless broadband device for Internet connection and cannot connect to the Canon using this device.
You need a wireless card that connects to the wireless router or wireless access point.
Otherwise you can connect to your printer using a printer cable.

Firstly you need to ensure that both devices have wireless, if the laptop does not, you will need to buy a dongle. The set up will be as with blue tooth, go to add hardware and select wireless on auto dicovery the laptop shoul pick up the printer and connect.
Even easier if you have wirless software that came with the laptop search there and connect. Remember to set the wireless to re connect at logon.
Good luck

Look for a WiFi button to ensure it isn't off. If it isn't, then go to the Control Panel and go to Device Manager (Hardware Manager in Vista) and make sure the device disabled. Right click it and choose Enable. Should pick up your wireless.

This type of error message appear when we are trying to connect to the wireless network.
For Windows(xp) perform the following steps:-
a)click on start menu and then go to control panel and then open network connections from there.
b)Under network connections an option for wireless connection exist , right click on that option and then click on properties.
c)Under wireless network connection properties there are three tabs general , wireless network and advanced.
d)Left click on wireless network tab and check the box which says use windows to configure my wireless setting's and click OK at the bottom.
e)Then , Right click again on wireless network connection and click properties and then again click on wireless network tab.
f)At the bottom of the wireless network tab you will have preferred networks and in that small box yo will have list of networks and therefore delete all of them from there including the one you are trying to connect to.
g)On the right hand side of preferred networks you will have ADD click on that option and enter the details of your network manually.
SSID(name of the network)
Network Authentication:-Open if the security is WEP else WPA-Personal.
Encryption:-WEP for wep security TKIP/AES for WPA-PSK.
Network key/Confirm network key:-is the wep key or wpa-psk password.
Untick the box at the bottom that says the key is provided to me automatically.
Click OK at the bottom and close the properties window.
h)Then , Right click again on wireless network connection and then left click on view available wireless network.
i)List of available networks will be there , select the network you use and try connecting to it , it will get connected automatically.

This featue might be turned off and needs to be turned on by typing in the ip adress of router and entering the user name and password and change your wirless seting so it will ot do this.

to contect to your wireless you need to click on your wirless icon search for networks..the router your using should come up ...connect to that...it might ask to enter comfirmation key code..

I know it sounds stupid but a lot of people just forget to turn on the wireless switch.

You may want to check first if the router is being picked up by other computers just to eliminate the possibility of a busted router. If no other computers can pick up your Router's signal then it's the router that you need to replace. If other computers can pick up your router's signal, then it's the computer's wireless card that's busted.

look in your manual, turn off your internal modem, wifi. and then plug in your new adapter. restart and see how that works. if not then best buy has a great tec department