Wrench light on will not photo copy - Toshiba 1360 Black and White Copier

Press the MENU button, select the wrench, then the fifth item on the menu.

You may download a copy of the manual from here.

If the photos are on a memory card, format it. Memory cards should be formatted each time you finish downloading your pictures. FixYa is full of people asking how to salvage photos from cards that hadn't been formatted recently.

If the photos are in the camera's internal memory, format it.

The format command is setup menu. Press the MENU button, select the wrench icon, then select the camera-slash-card symbol. Full instructions are in the "Format Memory/Format Card" section of the manual (page 109 in my copy). If you need a manual, you can download one at
http://support.nikontech.com/app/answers/detail/a_id/13948

I have a TOSHIBA photo copy machine 2860 whic shows a red wrench error

you will need to reset your machine to clear the error.

Enter the SP mode by entering, Clear Modes, 1,0,7, then hold down the Clear/Stop Key for more than 3 seconds. Then enter the Copier SP mode.
To reset the DSM 651, enter the SC code reset(if you don't know the reset code check your manual, documentation or the side panels of your printer) and select '1'.
Next, depress the 'Photo mode' key. While depressing the 'Photo
mode' key, depress the # key at the same time and hold both keys for at least 3 seconds (it is not necessary to turn the main switch off and on). If the machine beeps 5 times, the reset was successful. If it only beeps twice, the reset failed, and you need to try the reset procedure again.

Press MENU to display the menu. Press cursor-left to enter the tabs, use cursor-up/down to select Setup (the wrench icon) and press OK. Select "Copy" and press OK. Select the top item (camera-to-card), press OK, then select "All images" and press OK.

Refer to the "Basic Camera Setup: The Setup Menu" section in the manual, particularly the "Copy" subsection (page 102 in my copy).

the little wrench means it has shut down because it has exceeded the maintenance count, probably for the cleaner web in the fusing unit. Call service at 1 800 243 5556

l For manual copy density adjustment, press the AUTO/
MANUAL/PHOTO ( / / ) key to select
MANUAL ( ) and adjust with the LIGHT ( ) and
DARK ( ) keys as desired.
l For photographs, select PHOTO ( ) and then adjust with the
LIGHT ( ) and DARK ( ) keys as desired.
l There are 9 exposure steps indicated by 5 indicator lights. (The
indicators light up one or two at a time.)
Successive pushes of the LIGHT ( ) key will change the
indicator lights in the order (3) / (3•2) /(2) / (2•1) / (1).
Successive pushes of the DARK ( ) key will change the
indicator lights in the order (3) / (3•4) / (4) / (4•5)/ (5)
The automatic exposure level can be adjusted to suit your copying
needs.
1 Press the AUTO/MANUAL/PHOTO ( / / ) key
to select the PHOTO ( ) mode.
2 Press and hold the AUTO/MANUAL/PHOTO ( / /
) key for approximately 5 seconds.
l The PHOTO ( ) indicator will go out and the AUTO indicator
will begin to blink.
l One or two exposure indicators corresponding to the automatic
exposure level which has been selected will light up. The factory
default setting is level “3”.
3 Press the LIGHT ( ) or DARK ( ) key to lighten
or darken the automatic exposure level as desired.
4 Press the AUTO/MANUAL/PHOTO ( / / ) key.
l The AUTO indicator will stop blinking and will light up steadily.
l This automatic exposure level will remain in effect until you
change it again by this procedure.
Automatic exposure adjustment
AUTO

This blinking wrench red light means that your copier needs to be serviced. How old is your copier or how many copy have you done with it ?
Otherwise, you may need to call a service man for it.

Does this help? You obviously have to insert the media type into the media slot on the far right.(omoademola) Using the top control panel Printing tasks Scanning/Copying/Faxing tasks Troubleshooting
The top control panel lets you print an image from a photo card, scan a document or image, and copy a document or image with the press of a button.
Button/Light: Function: 1 Power : Turns the All-In-One on or off. 2 Copy: light Illuminates when Copy Mode is selected. 3 Mode: Changes the copy, scan, or photo card mode. 4 Scan: light Illuminates when Scan Mode is selected. 5 Photo Card: light Illuminates when Photo Card Mode is selected. 6 Rotate: Rotates the image 90 degrees. 7 LCD Panel: Number of Copies- this changes the copy count. Note: This feature is not active in Scan Mode. 8 Display: Shows copy, scan, and photo card selections. 9 Resize: Enlarges or reduces the size of the image. 10 Page Preview: Shows a preview of the output. 11 Select: Secures an option. 12 Menu: Provides options for image. 13 Arrow : Scrolls left, right, up, or down. 14 Stop/Clear: Cancels a print job or clears a selection. 15 Color Start: Initiates color copy, scan, or photo card output. 16 Black Start: Initiates black copy, scan, or photo card output.