Frigidaire Affinity 5.8 Cu. Ft. Electric Dryer Logo
Posted on Feb 08, 2009
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Brand new Dryer starts then stops after 15 seconds

Dryer stops after just 15 seconds of running and the lights begin to flash that are below the start/pause button . The dryer is heating, but will not continue running until you have pushed cancel and then start again about three different times. There is also a clicking sound coming from the backside of the dryer that does not sound right. I don't think the dryer should be making this sound. Please help!!!

Answer This Question

1 Answer

Bill Dickerson

Bill Dickerson

Level 3:

An expert who has achieved level 3 by getting 1000 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Vice President:

An expert whose answer got voted for 100 times.

  • Master 979 Answers
  • Posted on Feb 11, 2009
Bill Dickerson
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Vice President:

An expert whose answer got voted for 100 times.

Joined: Dec 25, 2008
Answers
979
Questions
0
Helped
309283
Points
2196

Stop what you are doing. It is under warranty. This will be more costs and it is not necessary. It is a mfr problem.

  • Anonymous Jan 29, 2013

    If this isn't a new dryer but I have the same exact problem, what do you think could be causing it?

  • Bill Dickerson
    Bill Dickerson Jan 29, 2013

    I believe the t'stat is bad just from the sound of it. It has a high limit control on it that keeps it from overheating. That is the design of a high limit control. If it doesn't function properly, then the result is either shutting off prematurely or worse not shutting off if it gets too hot. This is a blessing in
    disguise. If not the hi limit, then something is wrong with the computer board. Thankfully, you are under warranty. As far as the clicking sound, it could be the drum is not set right or the belt that drives it could be too tight or loose. Without hearing the sound, that would be my guess. Call where you bought it from and put it on them. This should be covered.
    Good luck, Bill

×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Affinity Dryer Model AEQ8000FE0 stops after about 30 seconds and 3 lights blink.
check out these sites...

https://www.repairclinic.com/ProductDetail/689318?symptoms=1

https://www.appliancepartspros.com/repair-help/frigidaire-dryer-aeq8000fe0-repair/aeq8000fe0-wont-start.html

A call to their tech 800#s so you don't start throwing parts at it. :)

Best to you
Read full answer
Apr 18, 2023 • Frigidaire Dryers
0helpful
1answer

2006 PTCruiser Fob Buttons don't work on 2nd and 3rd fobs
2006 models program. differently Make sure to check the batteries in the fobs before starting.Note: You must have two valid keys to add a new key to the system.If you do not have two working keys you will have to have a locksmith program a key for you. step 1. Insert the first valid key into the ignition switch. Turn the ignition switch to the ON/RUN position for at least three seconds, but no longer than 15 seconds. Then, Turn the ignition switch to the LOCK position and remove the first key.
step 2. Insert the second valid key into the ignition switch. Turn the ignition switch to the ON/RUN position within 15 seconds. After 10 seconds, a chime will sound. In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key.
step 3. Insert the new key into the ignition switch. Turn the ignition switch to the ON/RUN position.within 60 seconds. After 10 seconds, a single chime will sound. In addition, the Vehicle Security Light will stop flashing. To indicate that programming is complete, the Vehicle Security Light will turn on again for seconds and then turn off.
The new key is now programmed.
The Remote keyless Entry transmitter will also be programmed.
Repeat this procedure to program up to eight keys.
Read full answer
May 10, 2019 • Cars & Trucks
0helpful
1answer

Kenmore electric dryer model 88042 runs but stops short beeping
Based on symptom and details, the control has detected a component failure. Since your model does not have digital display window in order to display a fault code, it will flash the four indicator lights of

Drying, Cool Down, Wrinkle Rid (Press Saver), and Clean Lint Filter will flash the number of times for the first digit of the code and the START indicator light will flash the number of times for the second digit.

Take separate counts of each indicator light, then repeat to confirm in order to be accurate in identifying the proper error code. The code is obtained by counting the number of times the lights flash. Example E24: The four indicator lights would flash twice indicating the 2 and the START indicator light will flash four times indicating the 4. The four indicator lights and the START indicator light

start flashing at the same time. The control will pause for 2 seconds, then repeat the code.

The failure is likely because of a faulty thermistor or because the heater is not working. It could have a broken heating element or a burnt wire connection at the control board. I would begin by accessing the thermistor and disconnecting it. The thermistor can be tested with an Ohm meter. The thermistor should measure approximately 50,000/5K Ohms at room temperature.

The heating element is located behind the drum and it can be disconnected and tested for continuity with an Ohm meter.

NOTE: Disconnect the dryer from the power supply before servicing.
Read full answer
Jun 02, 2018 • Kenmore Dryers
1helpful
1answer

I called myself programming the new keys for my pt cruiser, but,it didnt take. At first it would start and run for a few seconds, now it wont turn over.what did I do wrong and how can I fix this?
Takes the master key to get it started again. The security gives you 3 tries to get the vehicle started, after the third time, it kills the starter.
2002 Chrysler PT Cruiser Note: You must have two valid keys to add a new key to the system.
1. Insert the first valid key into the ignition switch. Turn the ignition switch to the
ON/RUN position for at least three seconds, but no longer than 15 seconds.
Then, Turn the ignition switch to the LOCK position and remove the first key.
2. Insert the second valid key into the ignition switch. Turn the ignition switch to
the ON/RUN position within 15 seconds. After 10 seconds, a chime will sound.
In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch
to the LOCK position and remove the second key.
3. Insert the new key into the ignition switch. Turn the ignition switch to the
ON/RUN position.within 60 seconds. After 10 seconds, a single chime will
sound. In addition, the Vehicle Security Light will stop flashing. To indicate that
programming is complete, the Vehicle Security Light will turn on again for
seconds and then turn off.
The new key is now programmed. The Remote Keyless Entry transmitter will
also be programmed during this procedure.
Repeat this procedure to program up to eight keys.
Read full answer
Oct 09, 2016 • Cars & Trucks
1helpful
1answer

Why does Bosch Logixx Dryer Condenser run for 10-20 minutes then stops, flashes the 'Start/Stop' button, inside light goes off and then after a short delay comes back on again and continues flashing?
I have no idea
Read full answer
Apr 20, 2016 • Bosch Dryers
1helpful
1answer

Brand new condenser vhc 680f starts cycle and then stops after ten seconds and lights flash. checked filter
Hi my dryer was the same. Apparently condenser dyers wont work under 5c, with all this mega cold weather my utility room was freezing brr and the dryer stoped after 10-15 sec and started flashing checked everything but still wouldn;t work. Found a swedish website (after spending DAYS looking for an answer) that said it mght be to cold so I brought the dryer into my house and wa hey its working again. Hope this helps xxx
Read full answer
Oct 18, 2009 • Mattel UB FUNKEYS Dream State Dyer and...
0helpful
2answers

Frigidaire Gallery dryer only runs for 15 seconds
hello mam please change the thermostat.
Read full answer
Oct 08, 2009 • Frigidaire Electric Dryer
0helpful
1answer

Hi, my machine starts for a few seconds then stops and pause button wont stop flashing, have tried turning off and on but same thig keeps happenig, please help x
if it is a HE kind of machine it is supposed to stop and start a bunch of times at the beginning of the cleaning cycle. Did you wait for a while to see if it ends up running the cleaning cycle?

the new machines are kind of freaky the way they work.

later
Read full answer
Apr 09, 2009 • Zanussi ZWD1470W Front Load Washer / Dryer
0helpful
2answers

Zanussi zdc46130w Fault.
I think you should read the instruction manual . 3 beeps means some information to begin a solutin.
Read full answer
Feb 15, 2009 • Zanussi TC7114W Electric Dryer
6helpful
2answers

Re set service light on a 2005 V 50
1. Press in and hold the odometer reset button.
2. Turn on the ignition to the run positon - not all the way to the start positon.
3. After about 15 seconds the orange "I" light (that warns the service needed message is present) begins to flash.
4. While it is flashing release the odometer button - if you do not do it in time the light stops flashing and will not reset.
5. Then turn off the ignition.
Read full answer
Oct 06, 2008 • 2005 Volvo V50
Not finding what you are looking for?

View Most Popular

Affinity 5.8 Cu. Ft. Electric Dryer

  • Dryers

Related Question

Affinity Dryer Model AEQ8000FE0 stops after about 30 seconds and 3 lights blink.

  • Frigidaire Dryers

Related Topics

821 views

Ask a Question

Usually answered in minutes!

Popular Questions

Kenmore Oasis dryer F40 error code

Frigidaire GLEQ2152ES Electric Dryer

Error code on a Frigidaire affinity dryer E64

Frigidaire Dryers

Error Code E68 on frigidaire affinity dryer.

Frigidaire Affinity AEQ6000WH Dryer

What does error code E65 mean on dryer.. does not dry clothes well

Frigidaire FASE7021NW Laundry :...

My frigidaire affinity dryer displays LOC

Frigidaire Affinity 5.8 Cu. Ft. Gas...

Top Frigidaire Dryers Experts

Brad Brown

Level 3 Expert

19187 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Paul Bade

Level 3 Expert

1818 Answers

Are you a Frigidaire Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...