Question about Electrolux Washing Machines

1 Answer

Front load electrolux washer wont spin showed e58 now after attempting system clean e 57

Wont spin

Posted by on

  • John Patrick
    John Patrick Nov 28, 2017

    Check your wire harness at the wire tie attachment point on the motor. The factory has a tendency to cinch those ties too tightly. They can cut your wires over time leading to intermittent connections and therefore power surges leading to error messages!

    I found out the hard way after replacing the control board and the motor...

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Electrolux Master
  • 509 Answers

According to the alarm code E58 is usually a washing machine with inverter and means problem with inverter board or motor or wiring between inverter-motor.

Could be:

E58 - Inverter is drawing too much current (> 4.5A).
Abnormal motor operation (overload).
Motor-inverter wiring faulty.
Motor faulty.
Inverter board faulty.

E57 - Inverter is drawing too much current (>15A)
Motor-inverter wiring faulty.
Inverter board faulty.
Motor faulty.

Dado

Posted on Jan 28, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 207 Answers

SOURCE: front load washer

  1. Turn off machine and unplug it.
  2. Open filter it and clean it.
  3. Check if in pump turbine is clogged or jammed with foreign object. On some pumps you can test if turbine it rotates free using screwdriver or a finger.
  4. Check if the drain outlet pipe is clogged.

Unless pump motor is dead I'm 99% sure that either filter, pump and/or drain pipe are clogged.

Posted on Apr 20, 2008

  • 5 Answers

SOURCE: Kenmore HE2 front load washer. All cycle lights flashing plus spin and clothes clean lights on.

I'm sure this is probably too late, but hopefully it will help some else. I just had the same problem. First, unplug the power. Then take the lower front panel off and grabbed a bucket. Place the bucket under the large "plug" on your right. This is the drain. Slowly unscrew the drain plug, Hold your nose as it will probably smell. Allow the water and such to drain into the bucket. When you see the blob of wet lint drop into the bucket you will know why the machine refused to work. Make sure you clean the drain plug and screw it back in tightly. Put the lower panel back on and reconnect the power. I hope this resolves your issue.

Posted on Oct 10, 2009

torres No9
  • 27 Answers

SOURCE: error codes for Electrolux front load washer EWF 1087

E40 error is door interlock faulty, could be the lock or it could be the pcb u have to test them.

Posted on Jun 25, 2010

rylee_smith
  • 8619 Answers

SOURCE: my amana front load washer wont spin and is

Hi


Thanks for using FixYa. From what I understand the error code ND means “No Drain issue”. You’ll need to check for any restriction in pump assembly. It can also be due to a restricted drain hose or loose wire at pump. If after cleaning the drain hose the issue is not resolved then it means the pump has gone bad and unfortunately needs to be replaced. Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Posted on Aug 28, 2010

blueextc3221
  • 15935 Answers

SOURCE: washer codes F01/F33, have cleaned the pump and

The F33 error code indicates a pump drive system error. If the pump ohms out correctly & the harness is secure I recommend replacing the CCU (central control unit).
Please see the following image provided for instructions.

http://media.fotki.com/1_p,stwwfrggtqfbrbbxgtqsskgwtqkq,vi/wgtbwqwssxsbwkbdtfwxrbfbddwwf/1/1303472/5961857/image9159087223444281043img-or.jpg

Remember to disconnect power to the washer before attempting access.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question!!!!

Posted on Sep 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code E58


If you have a front-load washer that was manufactured by Frigidaire, the E58 error indicates high current on the motor. This could mean that the motor is bad, the bearings that the tub spins on are bad, or a problem with the speed control board. To test this, you'll need to access the motor and tub area of the washer. Unplug the power before opening the washer. Take the belt off the motor pulley and check if it spins freely. If it doesn't, then replace the drive motor. If it does spin freely, check if the large pulley on the tub spins freely. If that doesn't rotate, you'll need to replace the outer tub and spin basket in order to replace the failed bearings. If the pulley rotates easily, you'll need to check the motor windings. If the resistance is between 4-6 Ohms, the speed control board is probably faulty. If the resistance is not in the correct range, the motor is bad and needs to be replaced.

A Frigidaire washer technical data sheet is available here: http://manuals.frigidaire.com/prodinfo_pdf/webster/134542000.pdf .

If your washer is under warranty, contact the manufacturer. If you add a comment with the model number of your washer, I may be able to provide a source for the parts.

I hope this helps.

Cindy Wells

Apr 27, 2016 | Washing Machines

1 Answer

Why Electrolux front load making knocking sounds during spin cycle. Model ewf1087


Good Morning Friend,

I understand your Electrolux washer, model# EWF1087, is making knocking sounds during the spin cycle. In researching your model number, I show that your appliance was manufactured in Australia. If this were manufactured in the U.S., I would suggest making sure that the load was balanced. Balance your wash load and if you are still having trouble, I suggest contacting the manufacturer in Australia. Hope this is helpful.

-Best Regards-
WP

Jun 22, 2014 | Electrolux EW1200i Front Load Washer /...

1 Answer

What is electrolux front load washer E58 error code


Good Morning Friend, I am happy to assist you!

I understand your Electrolux washer is getting an error code E58. It could mean a number of issues, but primarily that the motor is overheating or a higher-than-usual motor current caused by other issues. Typically, an experienced technician would remove the belt to check the motor and motor pulley to ensure all is in working order first. Their next step would be to check the tub pulley and tub bearings. Last items they would examine would be the drive motor and speed control board by ohm measurement. Once the tech has ruled out a number of possibilities, he or she can pinpoint the exact problem and the necessary part to fix the issue. Since parts can often be quite costly, I would personally contact a professional to accurately diagnose your washer to determine the root cause to reduce the risk of unnecessary parts.

Hope this helps! - Z

Jun 04, 2014 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

Electrolux washing machine wont spin all the way


Not a solution, but I wonder if it thinks you've either selected no spin or it thinks the machine isn't drained and so won't spin or it thinks the load is unbalanced. You seem to have done everything logical so far.
Also look at all all connectors
Logic seems to dictate that if the motor/motor drive functionality and other diagnostics don't show any problems (although I must admit if it were possible I'd like to try another motor control board just to convince me it wasn't implicated) then it must be a logic/ sensor problem and maybe diagnostic mode doesn't check all sensors in the same way as would happen in normal use? Sorry I can't be of more help. (The motor brushes are probably ok but I'd check them anyway while you are in there) Do let us know if you find anything.

Apr 16, 2014 | Electrolux EIFLW55HIW Front Load Washer...

1 Answer

E58 Error Code


Hello Walter, thank you for your post!

I understand your Electrolux washer is getting an error code E58. It could mean a number of issues, but primarily that the motor is overheating or a higher-than-usual motor current caused by other issues. Typically, an experienced technician would remove the belt to check the motor and motor pulley to ensure all is in working order first. Their next step would be to check the tub pulley and tub bearings. Last items they would examine would be the drive motor and speed control board by ohm measurement. Once the tech has ruled out a number of possibilities, he or she can pinpoint the exact problem and the necessary part to fix the issue. Since parts can often be quite costly, I would personally contact a professional to accurately diagnose your washer to determine the root cause to reduce the risk of unnecessary parts.

Hope this proves helpful!

Jan 28, 2014 | Electrolux Washing Machines

1 Answer

Electrolux front load washing machine ew10001 spin cycle slow on "SPIN" setting runs fine through regular wash setting? any ideas?


Hello jamespeattie - Does the washer making a humming noise? If so, either the drain hose may be kinked or the drain in the house is clogged. Once you have confirmed and cleaned the hose and if issue continues contact a professional to move forward accurately. The unit may possibly have a faulty pump or control board.

Jan 02, 2013 | Electrolux EW1000i Front Load Washer

1 Answer

Water wont drain


Hi,

Problems with a washing machine not spinning or not draining are often inter related..

If you are having a problem with your top load washer then check out this tip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkout this tip...

Front Load Washing machine not draining and or not spinning


heatman101

Feb 12, 2011 | Electrolux Washing Machines

2 Answers

Water wont empty from machine.not spinning properly.clothes v wet at end of cycle.


Hi pauabreen

On the spin cycles (F or J) does your motor attempt to 'spin' up for about a second then basically fail.

Declan

Nov 01, 2010 | Electrolux EW1000i Front Load Washer

3 Answers

My electrolux ewf 1481 front loader wont spin


Open the flap, bottom right of the front panel and check the filter is clear. Most machines will not spin until they have expelled all the water. You may want to check the hose is not block and any connections to the sink if it's not on a standpipe.
Most new machines have quite sensitive out of balance detection so if it an odd load try again but add a few extra items to allow the machine to distribute the load evenly prior to spin. Hope this helps

Jul 07, 2010 | Electrolux Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

1,181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electrolux Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Poppa Maddo
Poppa Maddo

Level 2 Expert

371 Answers

Are you an Electrolux Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...