Question about Lutron ELECTRONICS S-1000H-LA SKYLARK SLIDE DIMMER SP LIGHT ALMOND
I recently had a dimmer installed in my kitchen. It's lighting a Lightolier track system with 4 50-watt fixtures on it. The dimmer was working fine for a month - until yesterday.
The light turns on/off without any problem, but the dimmer does not work. Does anyone have any ideas why the on/off would work but the dimmer doesn't?
I have other Lutron dimmers in the apartment and haven't had any problems with those.
What is the dimmer rated for? Your load on the track appears to be 200 watts. A standard dimmer will burn out, you need to look on the dimmer to see what it is rated for. Did it run hot with the dimmer before you had this problem? They make dimmers for higher wattage that will do the job for you.
Posted on Feb 09, 2009
The type of track heads you are using could be creating the problem. Are the lamps Par 20, Par 30 (screw in base) or MR-16 low voltage (push in base)? If the track head has a small (2"x4") box and uses MR-16 lamps then you need to use a dimmer specifically designed for ELECTRONIC LOW VOLTAGE. Incandescent lights (screw in base) and Electronic low voltage need a different signal to dim. Using a standard dimmer for electronic low voltage will work for a while, but then either the dimmer or the fixtures will go bad. If your lamps are incandescent or halogen you may have just had a bad dimmer. (Not common for Lutron products) but the part number you list should be good for 1000watts and should not be the issue.
Please see "Dimming Basics" under the helpful information tab for a better explanations of the two different styles of dimming. Hope this helps!
Posted on Oct 09, 2009
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
there is not way to know how the wires are run by the description.
it is possible to connct true 3-way switch, it will required additonal pair of wires to all 3 switches (meaning 3-14/3 wire).
so call 3-way switches is only two way. I have not seems a real 3-way switches.
go to the following site. they a connection diag. for the switches.
Posted on Mar 30, 2009
SOURCE: LUTRON DIMMER
The Lutron Maestro dimmer isn't rated or designed to operate low voltage lighting as it is a 120 V-AC rated electronic dimmer. You should either install a standard low voltage ON/OFF switch on this installation or obtain a dimmer rated for use on low voltage lights.
You need special low voltage dimmer designed for use on the low voltage pucks lights you have installed. Usually the low voltage is either 12, 24, or 36 volts, depending on the manufacturer of your particular light set. Once the correct dimmer is in place, the problem with the flickering and pulsing of the lights, should cease.
If you still are having this problem and you can't find a low voltage dimmer, you can contact the maker of your low voltage light kit and they can provide you with an acceptable dimmer option for your lights.
Most Home Depot and Lowe's carry the low voltage puck light kits, and usually have accessories for these lights, including dimmer switches that will work with them.
Hope you find this Very Helpful and best regards!
PS: I found this old, unanswered question and wanted to provide a solution to close out the problem and clear the question from the site.
Posted on Sep 10, 2009
Tips for a great answer:
Aug 11, 2013 | Electrical Supplies
Sep 11, 2011 | Electrical Supplies
Jun 04, 2011 | Lutron Electronic Low-Voltage Dimmer...
Mar 03, 2011 | Philips Lightolier Onset 600W Incandescent...
Jan 04, 2011 | Lutron 3-Way Rotary Push On/Off Dimmer
Dec 24, 2010 | Lutron Electrical Supplies
Nov 15, 2010 | Lutron #DVW-603PGH-WH 600W White Single...
Feb 07, 2010 | Lutron MIR-600 Remote Control
Jan 14, 2010 | Lutron GRX-TVI Grafik Eye 10 Volt...
5,331 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: