Dyna-glo parts I have a natural gas wall mounted Dyna-glo heater about 5 years old . Model # is RMC-40NGT.... I am trying to find a source for replacement parts as i believe that the thermocouple has died. The pilot lights but goes out after releasing it .. Sometimes it will light but goes out a few seconds later, and a small "click is heard.. Dyna Glo RMI 80 NGT Pilot stays lit. Fires up runs shuts off but will not relight unless you turn up stat. but the pilot does stay lit.

dyna glo natural gas heater Questions & Answers - Fixya

www.fixya.com > Forum > Tags

dyna glo ventless rmc50 ngt can this heater be changed from natural gas to propaneuse, ... Dyna Glo Natural Gas conversion to LP Gas I have a Dyna-Glo natural gas space ... Question about D-E36 Infra-Red Wall Mounted Panel Heater ... dyna glo heater model #RMC-40GT I believe on your particular model , that you ...

Parts for Dyna Glo, Thermoheat and Dyna Glo Pro Heaters

spaceheaterparts.com/category.sc?categoryId=13

Shop Dyna Glo, Thermoheat, Dura Heat, Workhorse LP and oil fired htrs ... Circuit Board 2201181 Dyna Glo & Thermoheat 150k Nat Gas Htr RMC-FA150NGDGD ... This spark plug (ignitor) is used on Dyna Glo and Thermoheat 40K btu LP.

Propane Wall Heaters - Walmart.com

www.walmart.com > ... > Heaters

WalmartDyna-Glo IR18NMDG-1 18,000 BTU Natural Gas - Infrared Vent Free Wall Heater. $170. ... Dyna-Glo 40K Liquid Propane 360-Degree Tank Top Heater. $88.00 ... Dyna-Glo Deluxe RMC-FA125DGD Portable Gas Powered Forced Air Heater.

1352062 Dyna Glo Natural Gas conversion to LP Gas

162.220.53.34/F/.../t1352062-dyna_glo_natural_gas_conversion_lp_gas

I believe on your particular model , that you have to replace the entire pilot assembly. As the thermocouple is an intricate part of it. In which case any LP or Natural Gas heater's pilot assembly will fit it. You will have to secify either Natural Gas or LP Gas when ordering.

I have provided 2 links to where you can purchase the pilot assembly you need.

http://www.mrheater.com/OrderParts2.aspx?catid=57

http://www.aandbsales.com/index.html



I hope this helps you & thanks for choosing FixYa.

CHANCES ARE YOUR GAS VALVE IS DEFECTIVE. THE SAFEGUARD PURPOSE OF THE VALVE IS TO PREVENT GAS FLOW IF THERE IS ANY REASON THE SAFETY FACTORS DON'T CHECK OUT RIGHT.

Hmmm ... where did you buy the last one? Are they out of business?

Here is what I found when I used Google:

http://www.mytoolsbee.com/cat164509.html

Ace Hardware may be a place you can order this stove from also.

Thanks for your question at FixYa.com

If it is a few years old, it could be the thermocouple. These are usually available from Lowes. Take your model/serial # and if you can, take the old part too.

I had the same issue. Iwent to the local harware store and bought heay duty mirror hangers. They work great for only a few bucks.

Thanks for the response......when I mentioned in the original problem of getting no gas that was with depressing the safety switch to light the furnace,,,,,,,,,I still get no gas when this switch is pressed.....I was looking at the furnace today and noticed there are a couple different lines running through different parts......I'm not sure which is a sensor bulb.........do you a reference site on the web that can help me or a place to find a manual for a dyna-glo heater ?

I have the same one i am looking for the wall brackets, I lost mine. I also bought mine at a garage sale the people had it attached to the wall completely hooked up .they had no fire backer on it .They only took it off the wall when i purchased it

the "click" you hear is the pilot valve closing. the pilot valve is spring loaded to shut off when a flame is not detected or is detected then is not. try this desatech site. it is for reddy heaters but they might have the thermocouple you are looking for.
www dot desatech dot com or
www dot robinrents dot com/heaterparts.htm

We had a problem keeping the pilot light to stay on, and this site recommended that it could possibly be the thermocoupler that was causing our problems also. We ordered the thermocouple, put it on,hooked it back up and it worked great! Thank you so much.
ordered thermocouple from www.masterparts.net