How do I clear the fault 103 Long range radio?

Does the system have an amplifier ?
Circuit/System Verification
Radio ON, Rear Seat Audio (RSA) OFF (if equipped), adjust the fade and balance controls on the radio to test all four channels individually. Each of the four channels should produce clear and even sound.
Without Amplifier Radio ON, verify clear audio is heard from each audio speaker.
?‡'
If audio is inoperative from all speakers, replace the radio.

?‡'
If audio is inoperative from one or more, but not all, speakers or the audio emitted from the speakers is not clear, refer to Speaker Circuit Malfunction - without Amplifier.
With Amplifier Radio ON, verify clear audio is heard from each audio speaker.
?‡'
If audio is inoperative from all speakers, refer to Amplifier Circuit Malfunction.

?‡'
If audio is inoperative from one or more, but not all, speakers or the audio emitted from the speakers is not clear, refer to Speaker Circuit Malfunction - with Amplifier.

Circuit/System Testing
Speaker Circuit Malfunction - without Amplifier

1. Ignition OFF, disconnect the harness connector at the appropriate speaker.
2. Radio ON, test for 5.0-7.5 volts between the signal circuit terminal A and ground.
?‡'
If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.



?‡'
If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the radio.


3. Test for 5.0-7.5 volts between the signal circuit terminal B and ground.
?‡'
If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.



?‡'
If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the radio.


4. If all circuits test normal, replace the speaker.

A quick google search yielded a theoretical range of 2 miles. This range is as the crow flies, and assumes an unobstructed open area, with no interference. In practicality, the radios will reach from one side of a side to another maybe a bit further. When Outside on a clear day in a city a football field or two will probably be the max. The range greatly depends on where you are located; buildings, power lines, and cars will interfere with the signal.

There are several sufix numbers after your model number so I just picked one, They are often the same as they usually keep the same wiring harness and circuitry through out many.Here's what I've found, Electronic control has detected a fault
condition. Press CLEAR/OFF to clear the display and stop the
beeping. Reprogram oven. If fault remains, record fault number.
Press CLEAR/OFF and contact a Service Professional. See:
https://www.searspartsdirect.com/partsdirect/user-manuals/GLEF396ABA-Frigidaire-Parts-Range-Parts-manual#
or choose from your complete model number:
https://www.searspartsdirect.com/model/search.html?q=GLEF396
Good luck

Check 103 on Ademco alarm system would usually tell me that you had your back up radio upgraded, but installer did not remove old back-up radio properly. If this is the case service call sould be or would be free.

I waited until the next morning and hit the cancel button. It cleared the error

Oven control beeps and displays any F code
error (for example F11).

Electronic control has detected a fault condition. Press CLEAR/OFF to clear the display
and stop beeping. Reprogram oven. If fault recurs, record fault number. Press CLEAR/
OFF and call your dealer or authorized service agent for assistance.

Oven control beeps and Electronic control as detected fault condition.
Press CLEAR to clear the display and stop displaysF1,F3, F7 ,or F9 beeping.
Program oven again.If fault recurs,record fault number.
Press CLEAR and contact your Sears authorized qualified service agency.

Hello rusalderman,
Welcome to fixya.
Happy to help.

You said, your range has an error code F 1 stove beeps.
This should reset the system.

A Solution to Common Problems
Oven control beeps & displays any F code error (for example
F1) - Electronic control has detected a fault condition.
Press CLEAR/OFF to clear the display & stop beeping.
Reprogram oven. If fault recurs, record fault number. Press CLEAR/OFF &
contact an authorized service agent.

This should resolve your problem and reset the system.

Please remember to leave a rating when you are finished.
Let me know. Hopefully it will be a solved.
Thank You , Huuum

F-1 is a fault code.


Disconnect the power plug or turn range power off at circuit breaker. Wait a couple of minutes, then plug the range in or flip the range circuit breaker to ON.


Oven control beeps & displays any F  code error (for example 
F11) - Electronic control has detected a fault condition. Press 
CLEAR/OFF to clear the display & stop beeping. Reprogram 
oven. If fault recurs, record fault number. Press CLEAR/OFF & 
contact an authorized service agent.