Quickcam installation I have windows xp. wizard says to plug in usb for quickcam. Computer indicates no connection. I turned off firewall and shield deluxe before installation. I am not aware of any spyware. Any suggestions or checks?

Hi, Logitech Camera has a usb cable come together with it. Just connect to USB port in the back of your computer. Wait for a while, windows will ask for driver of this Logitech Camera, insert the driver disk(if you don't have the disk, google the serial of the camera with word "driver" or go to Logitech Website, then download correct driver for your operating system, XP or Win7). Just follow instruction of wizard to complete the installation.
Hope this will help. Thanks for reading.

After you install Microsoft Windows XP Service Pack 2 on a computer that is running Microsoft Windows XP, the universal serial bus (USB) drivers do not appear to update. CAUSE After you upgrade from Windows XP to Windows XP Service Pack 2, the USB drivers... loadTOCNode(1, 'cause'); After you upgrade from Windows XP to Windows XP Service Pack 2, the USB drivers appear with the earlier version numbers, even though the files have been updated. Back to the top RESOLUTION To resolve this problem, install Windows XP SP2, and then update the drivers for... loadTOCNode(1, 'resolution'); To resolve this problem, install Windows XP SP2, and then update the drivers for the USB devices that are connected to your computer. To update these drivers, follow these steps:

1. Click Start, click Run, type devmgmt.msc, and then click OK.
2. Double-click the type of device that you want to update.
3. Double-click the specific device that you want to update.
4. Click the Driver tab, and then click Update Driver.
5. Follow the instructions in the Hardware Update Wizard.
6. Repeat steps 2 through 5 for each USB device.

Note You can also install Windows XP SP2, and then disconnect and reconnect the USB devices that are connected to your computer. By doing this, you start the Plug and Play utility. The Plug and Play utility updates the version numbers for the drivers.

Installing USB sound card (any windows)

1. Do not connect or plug the USB sound card
2. install the software and driver
3. restart the computer
4. connect the USB Sound Card
5. windows found new hardware
6. select find hardware automatically.
7. if windows cant find the driver select browse CD (contain driver)
   

i have 3 soundcard installed in my computer (XP Pro SP2,Vista Enterprise,Ubuntu Linux) 1 built in and 2 USB.

built in I use for speaker, 1 USB I used for monitor to my DJ mixing software, 1 USB I used for telephone(VOIP)

Here you go, a guide on how to fix the issue

1. Download QuickCam 8.4.8 with driver for WinXP.
2. Install WinRAR if not already installed yet.
3. Open the setup installer qc848enu.exe and unpack its contents to a folder. Alternatively, right click on qc848enu.exe and select “Extract to qc848enu\” option.
4. Insert or plug in the Logitech QuickCam Messenger to a USB port if not already done so.
5. An “Driver Software Installation” icon in systray (notification area) should appear, which will pop up detailed message if click. It should fail, and “Add Hardware Wizard” dialog window will appear. Choose to install the driver manually by instructing the Wizard to locate and look for the web cam driver inside the Drivers folder under the unpacked folder of the qc848enu.exe setup program. You can use browser button to select the folder.
6. Windows Vista should grab the XP driver and install it properly.
7. Download the latest version (10.5.1) of Vista compliant QuickCam software from Logitech to install the software on Vista.
8. Run the setup (qc1051enu) normally. You may need to skip the detection of webcam near the end of installation process.

Wireless Adapter Installation

A. Install the software.

Note: Firewall and anti-spyware need to be disabled. They sometimes treat software installation as a behavior of a spyware and therefore will prevent installation.

Windows XP:

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter Resource CD into your CD-ROM drive. The CD main page shown at the right will then load.
3. Click the Install Driver & Utility.
4. Please make sure that you follow the Install Shield Wizard steps. Click Finish when done and turn off your computer.

Windows 2000/ME/Win98SE:

Note: Windows 2000 may require you to be logged on with administrator rights.

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter resource CD into your CD-ROM drive. The setup page will then load.
3. Afterwards, click on the Install Driver & Utility link.
4. Make sure to follow the Install Shield Wizard steps, and click Finish when done to restart your computer.

B. Install the adapter.

Windows XP:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Please insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. When the Found New Hardware Wizard displays, please click on Next and then follow the prompt. If you are prompted with a Windows XP Logo testing message, just click on Continue Anyway.
5. After the installation completes, click Finish to close the wizard.

Windows 2000/ME/Win98SE:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. On the Found New Hardware Wizard, click on Next, then follow the prompt to proceed.
5. After the installation completes, click Finish to close the wizard. Please make sure that you can see the NETGEAR icon located at the lower right portion of your computer screen.

Note: If Windows displays Digital Signature Not Found warning, click Yes to continue.

C. Configure the NETGEAR adapter.

1. Please Double click on the NETGEAR icon on the right lower end portion of your computer.

Note: If you do not see the icon, click on Start and go to Programs. Locate the NETGEAR Utility and click on the NETGEAR Smart Configuration Utility.

2. Click on the Networks tab.
3. Click on the Scan button.
4. Select the Network Name or SSID of your wireless network.
5. Click on the Connect button.
6. You will be directed to the Settings tab.
7. Type a name for the Profile.
8. The Network Name (SSID) will be the same with your wireless network.
9. Make sure that the Network Type is set to Access Point (Infrastructure).
10. Select the Security that you are using on your wireless router.
11. Click on Save Profile.
12. Click on the Apply button.

Wireless Adapter Installation

A. Install the software.

Note: Firewall and anti-spyware need to be disabled. They sometimes treat software installation as a behavior of a spyware and therefore will prevent installation.

Windows XP:

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter Resource CD into your CD-ROM drive. The CD main page shown at the right will then load.
3. Click the Install Driver & Utility.
4. Please make sure that you follow the Install Shield Wizard steps. Click Finish when done and turn off your computer.

Windows 2000/ME/Win98SE:

Note: Windows 2000 may require you to be logged on with administrator rights.

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter resource CD into your CD-ROM drive. The setup page will then load.
3. Afterwards, click on the Install Driver & Utility link.
4. Make sure to follow the Install Shield Wizard steps, and click Finish when done to restart your computer.

B. Install the adapter.

Windows XP:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Please insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. When the Found New Hardware Wizard displays, please click on Next and then follow the prompt. If you are prompted with a Windows XP Logo testing message, just click on Continue Anyway.
5. After the installation completes, click Finish to close the wizard.

Windows 2000/ME/Win98SE:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. On the Found New Hardware Wizard, click on Next, then follow the prompt to proceed.
5. After the installation completes, click Finish to close the wizard. Please make sure that you can see the NETGEAR icon located at the lower right portion of your computer screen.

Note: If Windows displays Digital Signature Not Found warning, click Yes to continue.

C. Configure the NETGEAR adapter.

1. Please Double click on the NETGEAR icon on the right lower end portion of your computer.

Note: If you do not see the icon, click on Start and go to Programs. Locate the NETGEAR Utility and click on the NETGEAR Smart Configuration Utility.

2. Click on the Networks tab.
3. Click on the Scan button.
4. Select the Network Name or SSID of your wireless network.
5. Click on the Connect button.
6. You will be directed to the Settings tab.
7. Type a name for the Profile.
8. The Network Name (SSID) will be the same with your wireless network.
9. Make sure that the Network Type is set to Access Point (Infrastructure).
10. Select the Security that you are using on your wireless router.
11. Click on Save Profile.
12. Click on the Apply button.

Normal 0 You need to go to the manufactures site and download the VISTA driver for the camera. Then follow the info below to install the program.



Disconnect the Camera from the USB port and reinstall the CD or Downloaded software program. When the program asks you to connect the camera to the USB port, do so and it should work.
Hope this helps. Bud

This problem was caused by a compatibility issue between Windows Vista and Logitech QuickCam Messenger.
Logitech QuickCam Messenger was created by Logitech, Inc..
Recommendation
—————-
To search for similar devices that are compatible with this version of Windows, visit the Windows Vista Hardware Compatibility List website online.
However, it’s not totally out of hope for owner of Logitech QuickCam Messenger who has upgraded to Windows Vista. The following hack will use Windows XP driver (a common trick to use non Vista compliant device) to install the webcam in Vista:

1. Download QuickCam 8.4.8 with driver for WinXP.
2. Install WinRAR if not already installed yet.
3. Open the setup installer qc848enu.exe and unpack its contents to a folder. Alternatively, right click on qc848enu.exe and select “Extract to qc848enu\” option.
4. Insert or plug in the Logitech QuickCam Messenger to a USB port if not already done so.
5. An “Driver Software Installation” icon in systray (notification area) should appear, which will pop up detailed message if click. It should fail, and “Add Hardware Wizard” dialog window will appear. Choose to install the driver manually by instructing the Wizard to locate and look for the web cam driver inside the Drivers folder under the unpacked folder of the qc848enu.exe setup program. You can use browser button to select the folder.
6. Windows Vista should grab the XP driver and install it properly.
7. Download the latest version (10.5.1) of Vista compliant QuickCam software from Logitech to install the software on Vista.
8. Run the setup (qc1051enu) normally. You may need to skip the detection of webcam near the end of installation process.

Voila, you can now use the Logitech webcam to capture images or use it in conjunction with video chat in IM programs such as Windows Live (MSN) Messenger, AIM Messenger, Yahoo! Messenger, Skype or run Logitech VideoCall.

i hope thist post can solve your problem


thank's


cropp

Wireless Adapter Installation

A. Install the software.

Note: Firewall and anti-spyware need to be disabled. They sometimes treat software installation as a behavior of a spyware and therefore will prevent installation.

Windows XP:

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter Resource CD into your CD-ROM drive. The CD main page shown at the right will then load.
3. Click the Install Driver & Utility.
4. Please make sure that you follow the Install Shield Wizard steps. Click Finish when done and turn off your computer.

Windows 2000/ME/Win98SE:

Note: Windows 2000 may require you to be logged on with administrator rights.

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter resource CD into your CD-ROM drive. The setup page will then load.
3. Afterwards, click on the Install Driver & Utility link.
4. Make sure to follow the Install Shield Wizard steps, and click Finish when done to restart your computer.

B. Install the adapter.

Windows XP:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Please insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. When the Found New Hardware Wizard displays, please click on Next and then follow the prompt. If you are prompted with a Windows XP Logo testing message, just click on Continue Anyway.
5. After the installation completes, click Finish to close the wizard.

Windows 2000/ME/Win98SE:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. On the Found New Hardware Wizard, click on Next, then follow the prompt to proceed.
5. After the installation completes, click Finish to close the wizard. Please make sure that you can see the NETGEAR icon located at the lower right portion of your computer screen.

Note: If Windows displays Digital Signature Not Found warning, click Yes to continue.

C. Configure the NETGEAR adapter.

1. Please Double click on the NETGEAR icon on the right lower end portion of your computer.

Note: If you do not see the icon, click on Start and go to Programs. Locate the NETGEAR Utility and click on the NETGEAR Smart Configuration Utility.

2. Click on the Networks tab.
3. Click on the Scan button.
4. Select the Network Name or SSID of your wireless network.
5. Click on the Connect button.
6. You will be directed to the Settings tab.
7. Type a name for the Profile.
8. The Network Name (SSID) will be the same with your wireless network.
9. Make sure that the Network Type is set to Access Point (Infrastructure).
10. Select the Security that you are using on your wireless router.
11. Click on Save Profile.
12. Click on the Apply button.

Error 2711
When receiving the 2711 error during Logitech QuickCam/Image Studio software installation, please perform the following steps:

1. Use Add/Remove programs in the Control Panel to uninstall any current installation of QuickCam/ImageStudio software. For Microsoft Windows 95, 98, ME or NT
   
   1. Click Start, Settings, then Control Panel.
   2. Double click the icon labeled Add/Remove Programs.
   3. Highlight the desired program in the list provided (QuickCam or ImageStudio).
   4. Click Add/Remove Programs located in the bottom right of the list provided.
   For Microsoft Windows 2000 or XP
   
   1. Click Start. followed by Control Panel.
   2. Double click the icon labeled Add/Remove Programs.
   3. Highlight the desired program in the list provided (QuickCam or ImageStudio).
   4. Click the button labeled Remove located in the bottom right of the program selected.
2. Navigate to C:\Program Files\Logitech.
   1. Double click the icon on the desktop labeled My Computer.
   2. Double click the icon labeled C:\(computer name).
   3. Double click the yellow folder labeled Program Files.
   4. Double click the yellow folder labeled Logitech.
3. Delete any folders for QuickCam/ImageStudio.
   1. Select the yellow folder with the QuickCam or ImageStudio names.
   2. Click the menu options for File, followed by Delete.
   3. Repeat for any other QuickCam/ImageStudio folders.
4. Delete all files located in the Windows temporary directory C:\Windows\Temp or C:\WinNT\Temp
   
   1. Double click the icon on the desktop labeled My Computer.
   2. Double click the icon labeled C:\(computer name).
   3. Double click the yellow folder labeled Windows or WinNT.
   4. Double click the yellow folder labeled Temp.
   5. On the menu across the top of the window, click Edit followed by Select All.
   6. On the menu across the top of the window, click File followed by Delete.
   7. Click OK.
5. Reinstall QuickCam/ImageStudio
   1. Remove and reinsert the QuickCam/ImageStudio CD and follow the prompts OR
   2. Double click on the downloaded ImagStudio file.