Maytag 24 in. MDBH950AWS Built-in Dishwasher Logo
cosimo granata
cosimo granata Posted on Jul 31, 2007
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Maytag dishwasher mdbh950awb

Hi i have a maytag builtin dishwasher mdbh950awb thats about 2 yrs old and now normal wash doesnt work heavy and light works only after pushing the buttons a few times and start a lot of times can you help i tried unplugging to reset to no avail! the button on the touchpad sometimes lights up sometimes does not.

Answer This Question
  • Home Dude Nov 17, 2007

    MDB-9

    Normal wash button dead, other wash cycles light up but no functions will work.





    Home Dude

  • onealsofva Apr 26, 2009

    Lightwash cycle on electronic keypad dead. Everytime we have an power outage, we loose a new function. As of outage last night, now the cycle time and time left now longer appears. It used to show how long the cycle ran for and how much time was left but now it is blank?

×

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

  • Master 5,911 Answers
  • Posted on Jul 31, 2007
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

Joined: Sep 29, 2006
Answers
5911
Questions
6
Helped
2734644
Points
22413

Sounds like you have a control panel and/or control board issue. Normally when operator functions fail or "halfway" work the main control board, associated keypad, or wiring are the likely suspect. Now...another remote possibility could be the door latch not closing properly. However, this would affect ALL functions. I hope this helps you.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Run a service test for kitchenaid dishwasher
Did you check behind the toe-kick panel for the tech data sheet? Assuming that you have checked and that it is missing, there here is the "secret keystrokes" that will make most Whirlpool/ KitchenAid/Kenmore/Maytag diswashers enter the diagnostic cycle:
Heated Dry - Normal - Heated Dry - Normal; or
High Temp - Air Dry - High Temp - Air Dry; or
Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy Saver Dry; or
High Temp Wash, Heated Dry, High Temp Wash, Heated Dry.

Note: On some of the newer Whirlpool, Kenmore, KitchenAid dishwashers, you start the diagnostic cycle by rapidly pressing the 3 left-most keys in the following sequence: 1 2 3, 1 2 3, 1 2 3.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

Read full answer
Oct 18, 2014 • KitchenAid KUDS30IXSS Builtin Dishwasher
0helpful
1answer

How much water does a dishwasher use per cycle
auto clean 4 to 10 gal
heavy wash 10 gal
normal wash 4 to 8 gal
light wash 4 to 6 gal
rinse only 2 gal
Read full answer
Jun 14, 2014 • Maytag MDB7100AWB Dishwasher
0helpful
1answer

Led light flashes 4 times, pauses then repeats
Which light blinks 4 times and pauses wash normal heavy etc if the model in the blue box is correct the to enter diagnostic press any 3 keys within 8 seconds I usually use normal and the 2 keys to the right all lights should light up if touch pad is up top where you had to open door to accomplish this then close the door after a pause the clean light will begin to flash example 7 flashes pause 1 flash these are your fault code it will do this 3 times for each code. The tech sheet should be behind the toe panel located below the dishwasher door which just repeats what I explained.
Read full answer
Feb 04, 2014 • KitchenAid KUDE70FXSS Builtin Dishwasher
0helpful
1answer

Low water level
Try to unstick the float. The float tells the DW how much water is in it at any given time. It is shaped like a mushroom on the bottom of the DW basin. Gently pick it up and set it back down. Does it seem free? Try the cycle again.
Read full answer
Jan 10, 2014 • Samsung DMT400RHS Builtin Dishwasher
0helpful
1answer

Start/cancel buttons no longer work
Dear Sir:
see this possible causes:
Power from the house
see for a blown fuse or c.breaker reset.
Door switch
this is important test it.
Wiring
loose or breake wires
Timer or selector switch
can be defective.

see the w. diagram for HELP. attached.
Now see if the starting relais is closed,because if are OPEN the machine will not work. Test it.
5_5_2012_4_23_21_pm.gif
Read full answer
May 05, 2012 • Maytag MDB7609AWS Builtin Dishwasher
0helpful
1answer

MDB7749AWB
Hello I had the same issue the sequence for resetting the panel is;
heated dry...normal...heated dry...normal
all the lights will go on then off. on my machine it started the normal wash cycle. I let it run normally so far this worked.
Hope this helps.
Read full answer
Dec 30, 2011 • Maytag MDB7749AWB Builtin Dishwasher
0helpful
1answer

Control panel lights but won't start
the front control panel fries out.. We had to have ours replaced after 7 months ... after that was replaced it only lasted 2 months... WE ARE VERY disappointed and will be calling once again tomorrow. The dishwasher is not even a year old yet!
Read full answer
Aug 16, 2009 • Maytag MDC4650AW Built-in Dishwasher
1helpful
1answer

Runs forever! even on Normal wash...help !!
Check to make sure you heating element has not failed. Dishwashers of today heat the water periodically through out the cycle and if the element has failed. The heating delay light is the indicator that tells you that it is trying to heat the water.
Read full answer
Feb 26, 2009 • Frigidaire 24 in. FDB635RF Built-in...
0helpful
1answer

Runs forever! even on Normal wash...help !!
The most obvious failure would be the mechanical timer that is behind / part of the knob used to select the cycle.

But, you may want to inspect the heating element in the sump area -- some dishwashers will wait (and wait) for the water temp to come up high.

Good Luck!
Read full answer
Feb 25, 2009 • Frigidaire 24 in. FDB510LC Free-standing...
0helpful
1answer

Maytag MDBH950AWB Leaking
Hi,
Here is a tip that I wrote about dishwashers and them leaking.

Leaking Dishwasher

heatman101
zgwerty
Read full answer
Feb 23, 2009 • Maytag 24 in. MDBH950AW Built-in...
Not finding what you are looking for?

View Most Popular

24 in. MDBH950AWS Built-in Dishwasher

  • Dishwashers

Related Question

Run a service test for kitchenaid dishwasher

  • KitchenAid KUDS30IXSS Builtin Dishwasher

Related Topics

834 views

Ask a Question

Usually answered in minutes!

Popular Questions

Maytag quiet series 300 no power to touch controls

Maytag 24 in. MDB5651A Built-in...

Maytag dishwasher legacy 300 quiet series

Maytag 24 in. MDB9750AW Dishwasher

Maytag Dishwasher flashing lights

Maytag MDB7100AWB Dishwasher

Loud noise maytag dishwasher quiet series 100

Maytag 24 in. MDB9750AW Dishwasher

Maytag Dishwasher won't drain

Maytag 24 in. MDB5600A Jetclean II...

Top Maytag Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

Brad Brown

Level 3 Expert

19187 Answers

Paul Bade

Level 3 Expert

1818 Answers

Are you a Maytag Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...