Always light on

Go to settings >> system >> About device. Find "Build number" and click 6 times fast on it. Now go to Developer options >> Drawing Section or Rendering Section >> Find "Turn off hardware overlays" or "disable hardware overlays" >> This will force the phone to always use GPU for screen adjustments. no more flickering.

Hello,

I had the same thing with an MSI notebook. This is most likely a hardware issue and can only be fixed permanently by replacing the motherboard.
For me one trick worked though... when turning it on, instead of pressing once, press the power button rapidly multiple times. I've been using my notebook like this for half a year now, its quite tricky, doesn't always work, but cheaper than a new mobo.

Good luck!

IT owes to that the screen of his this exhausted laptop or badly cofigurada can form her in the control panel

The superscope uses an infared sensor as well as light detection to work
Chances are that some form of interference is going on so try moving your sensor
You could als ojust have a bad super scope and It's dying out
Thank you for your time Good luck and I hope this helps

More information is needed.

Open following link for Intermatic-Malibu resources:
http://waterheatertimer.org/Malibu-power-pack-stopped-working.html

You say clock doesn't work.
Add a comment with following information:
Do you have timer with analog dial?
Does dial rotate as time passes?
Does dial keep good time?
Have you put the black and red trippers in place?
Are trippers push all the way down?
Have you set current time by rotating clock dial 2 full turns before rotating dial to current time?

Intermatic/Malibu ML series timers come with 5-year warranty.
Product is covered by warranty.

Upvote the help.
And take advantage of fixya expert assistance live.
For a price, expert works with you while you work on timer or any do-it-yourself project.
Fixya is always less expensive than a service call.

Setting Top of Form, Forms Tear-Off ON

(Step A)

! If you turn the platen knob when the printer is turned

on, you will cause the Top of Form to mis-align. Always

turn the printer off before turning the platen knob!

1 Turn the printer ON.

2 Park the paper.

3 With paper out of the unit, (red alarm light should be on)

press SHIFT (1) and QUIET/TOF (5) to reset the current

Top of Form.

4 Press FF/LOAD (3) to load the paper.

5 Press SEL/MENU (6) to take the printer off line.

The SEL light goes out.

6 Wait until the paper moves up to the tear position, then

press and hold TEAR (4).

The paper moves to the current Top of Form.

Keep pressing and holding TEAR.
7 Press and hold SHIFT and release TEAR.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Setting Top of Form, Forms Tear-Off ON

(Step A)

! If you turn the platen knob when the printer is turned

on, you will cause the Top of Form to mis-align. Always

turn the printer off before turning the platen knob!

1 Turn the printer ON.

2 Park the paper.

3 With paper out of the unit, (red alarm light should be on)

press SHIFT (1) and QUIET/TOF (5) to reset the current

Top of Form.

4 Press FF/LOAD (3) to load the paper.

5 Press SEL/MENU (6) to take the printer off line.

The SEL light goes out.

6 Wait until the paper moves up to the tear position, then

press and hold TEAR (4).

The paper moves to the current Top of Form.

Keep pressing and holding TEAR.
7 Press and hold SHIFT and release TEAR.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe



I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

The timer doesn't know what time it is until you set current time.
The yellow outlets are controlled for 12 hours, and you can determine when those hours occur when setting current time.
http://waterheatertimer.org/GE-timers-and-manuals.html#zilla

If you want timer to control one lamp with both day and night schedules, you have to adjust current time setting so lamp schedule falls within a 12 hour period. If that schedule doesn't fit, then buy a second timer.

Absolutely feel obligated to upvote the help.
Or take advantage of fixya expert assistance live.
For a price, expert works with you while you work on timer or any do-it-yourself project.
Fixya is always less expensive than a service call.

Hello Emilio, it seems that your camera was in contact with water or Coca-Cola. In order to repair it you should change light guide plate part number: 147913011 or LCD part number: 180572011 or both. Best regards, Arpi