I cannot connect to my belkin connect n150 router after enabling it as an access point. Green light shows up on router and wireless network shows up but no connection when clicked. I cant connect via

Connect the Belkin router to a computer with an ethernet cable
Open a web browser and enter 192.168.2.1 in the address bar.

Check the Network name and Password - make a note of them.

Setting up the Belkin router
Belkin

N150 Wireless Router
Part # F9K1001
Belkin

Connect a computer to one of the Belkin's "LAN" ports with an Ethernet cable.Open a Web browser and enter "192.168.2.1" into the address bar. Press "Enter."Click "Login," then click "Submit."Make a note of the WLAN MAC address on the Status page.Click "Wireless Bridging" under the "Wireless" category.Click to check the two boxes "Enable wireless bridging" and "Enable only specific access points to connect."Type the MAC address of the Belkin router and the MAC addresses of the other wireless routers or access points that are participating in the bridged WDS network. If using Belkin devices, repeat the previous steps to obtain the WLAN MAC addresses, otherwise refer to the owner's manual of the wireless device to find the WLAN MAC Address.Click "Apply Changes" to save the settings.

Your Belkin may be using WPA2 for security. Access the router and change it to WPA Personal.

Your router should broadcast 255 IP addresses as long as DHCP setting is enabled, which it is by default.
Here is the manual:

http://cache-www.belkin.com/support/dl/MAN_F7D5301_v1_8820-00696_Connect_N150_Router.pdf

Click on this link or copy and paste the complete link into your browser.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

As i understand you have a router provided by your ISP: MTNL, you need to configure the Belkin router in Dynamic mode and not in PPPoE. Then restart the devices by unplugging the power from MTNL router and Belkin. Wait for 20 secs, then power up MTNL router 1st, wait for all lights to get steady and finally power up the Belkin wireless router. Then you will find the modem and internet light lit up properly.
For any further clarifications, revert!

Thanks and regards,
Arvind

You can secure your wireless network wit WEP or WAP code.
For that Connect your router to computer with ethernet cable then you can access it with following default link.
http://192.168.0.1
or
http://192.168.1.1
For belkin router http://192.168.15.1
or
http://192.168.2.1

If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it.
Then it ask for user name and password.
Type user as "admin" and password as "admin" or "password" or blank.
Then you can see configuration page of router.
Click on wireless settings then enable WEP Security then add WEP code .It is your password to connect wi fi.Then save settings and restart router.
Then you can connect your wi fi network with that code.
Thanks for using FixYa.

Should be a reset button on the rear of the router. You will need a thin pin or a ball point pen to push it in. Hold it in for about five secounds when router is powered up and it will reset itself to the settings it had when you got it out of the box.

When the Security light on your Belkin n150 is off, it means that the wireless security is off.

The WPS button is used to setup the wireless security. To enable security, you will need to determine which standard you want to use. To access the security settings follow the steps below:

1. In the address bar of your Internet browser, type "192.168.2.1". Then press the "Enter" key.

2. It will prompt for a password to access the Router’s Web-Based Advanced User Interface. By default the password is blank.

3. Click "Security" on the "Wireless: tab.

You actually have a couple of issues here. Fix these in this order. 1.) Login to router and turn off wireless (if you're not wanting to use wireless) 2.) Connect the ADSL modem CAT5 port to the WAN port of the Belkin router. 3.) Login to router and turn on NAT and make sure DHCP is enabled. 4.) On your Windows machine turn on DHCP under the network settings. This should allow your connection to be setup automatically and stop wireless access on the Belkin router. Let me know if you need more help. JC