REPLACEMENT BEATERS FOR CAMFIELD POWER MIX

Hi,

Please disconnect the power from the device for 5 minutes, reconnect and attempt to change the speed again.
If that does not work, please eject the beaters and attempt the change the speed with them ejected before re-adding the beaters. Thank you.

Question edited for clarity.

eBay probably.

Parts

https://www.google.com/search?q=west+bend+mixer+parts

https://www.google.com/search?q=beaters+for+west+bend+41016-9837&tbm=isch&ved=2ahUKEwjd18LjjIb3AhUghHIEHawIDUYQ2-cCegQIABAA&oq=beaters+for+west+bend+41016-9837&gs_lcp=CgNpbWcQAzoHCCMQ7wMQJ1CfJVj_TmDRW2gAcAB4AIAByAGIAfIKkgEGMTQuMC4xmAEAoAEBqgELZ3dzLXdpei1pbWfAAQE&sclient=img&ei=pgVRYt3sAaCIytMPrJG0sAQ&rlz=1C1QJDB_enCA643CA644

..

It's an antique. No parts appear to be available for it.

https://www.google.com/search?q=camfield+model+70+sm+6+ch+mixer+replacement+parts

..

First, is this a stand-type mixer? If so, have you removed the mixer head from the stand? The model # may be found there under the hinge on the mixer head. Second, if you still can't find a model #, why not Google images of B&D Multi-Mix units? It would probably help to put the model year in the search description, such as 1983 B&D Multi-Mix mixer. Once you find the matching image online, you should be able to find a model number.

There is a screw at the bottom of the motor head (flat head) you usually can't see it because of the top rim of the mixing bowl. hard to see and hard to reach, it may also be hard to turn due to "gunk" from mixing stuff (egg butter flour sugar) turn the screw counter clockwise to lower the motor head clockwise to raise it, you may also have the wrong size beater, it is not an uncommon problem, if you are the original owner and you have the original beater it should fix your problem with the adjusting screw, however I am not clear as to your model a 5SSWH would actually be a K5SSWH, which stands for kitchenaid 5 quart solid state white mixer, if this is your model number and you have the correct beater size then the adjusting screw will work to lower the head down, adjust it down using the stir or slowest speed just untill you can hear the beater "Ding" against the bottom of the bowl, then back it off a quarter turn to adjust properly. Hope this helps, let us know

Sadly, the service directions, while excellent, are for a Sunbeam Mixmaster Model 12...uselful for a Dormeyer only in the most general of terms.

how do you remove the power cord on dormeyer model 4300 mixer

Cuisinart hand mixers are not repairable. You can buy replacement accessories like beaters, but you can't buy any internal replacement parts.

I have a Cuisinart HM-70 and I stripped the plastic gears inside by trying to mix a really thick dough. It was easy to open and get to the plastic gears. When I called Cuisinart to try to get replacement gears, they said that they don't sell replacement parts and their hand mixers are not repairable. I looked all over the internet and no one sells internal parts.

Unless your mixer is still under warranty, I believe that you're out of luck and your mixer is headed to the electronics recycle pile.

Most handmixers today are sold with plastic gears - including high end brands like Viking. For me the lesson learned is to buy low end hand mixers (don't buy a top of the line 9 speed mixer) and treat them like they're disposable when they break.

JOE:You don’t say if you have a ‘tilt-head’or a ‘bowl-lift' mixer, but you can easily download a PDF version of your Owners Manual from the KA website (http://www.kitchenaid.com/flash.cmd?/#/page/home).Click on Customer Care>Locate Manuals& Guides> and enter the 6 character model number (in your case, use KSM90P)and select the last file listed that appear under Owners Manuals:KSM90PSWW0.pdf (2930.74 KB)and save that file to your PC.You’ll need to have Adobe Reader to be able to open it. Turn to Page 11 and you will find the instructions for adjusting the mixer head height.I have extracted the instructions below:
Beater to Bowl Clearance
Your mixer is adjusted at the factory so that the flat beaterjust clears the bottom of the bowl. If for any reason, the flat beater hits thebottom of the bowl or is too far away from the bowl, clearance

Tilt-Head models
• Unplug mixer.
• Lift motor head.

• Turn screw (A) SLIGHTLY counter clockwise (left) to raise flat beater or clockwise (right) to lower flat beater.
• Make adjustment with flat beater, so it just clears surface of bowl.
If you over adjust the screw, the bowl lock lever may not lock into place.


Bowl-Lift models
• Unplug mixer.
• Place bowl lift handle in down position.

• Turn screw (B) SLIGHTLY counter clockwise (left) to raise flat beater and clockwise (right) to lower flat beater.
•Make adjustments with flat beater, so it just clears surface of bowl.

I hope this helps! –Howard, Burke, VA
If this solution has helped you, please rate it, thanks!.hslincoln

does the motor still run or does it slowly start to get less loud? or is the beater assembly that dosnt work? two different issues. if the motor runs but dosnt beat then its the planitary gears that are ground out and need replacing. if the motor slowly dies out then you need to replace the motor.