Error code 8

Question edited for clarity.
Question moved from Firearm Optics category.

It looks like you solved it yourself as to what is means

https://www.manualslib.com/manual/1197834/Haier-Hw80-B14266a-Ec.html?page=21

More here, but no one gives the reason.

https://www.google.com/search?q=haier+HW80+washing+machine+error+code+Fb

Model number appears to be incorrect as 'PD1626'?

https://www.google.com/search?q=HW80+PD1626

..

The Heller DWH3 appears to be a Dishwasher, so I moved category from Laundry Washing Machines.

The Heller appears to be a little known make here in North America, and the only similar name 'Hella' I know makes car spotlights. If it shares codes with Haier, it is this, the Flood Protection Device and is very common. There is a tray and sensor in the base.

E6: All four lights flashing

Haier dishwasher E6 error code indicates that the flood protection device has been activated and the water supply will need to be turned off, stopping any more water from flowing into the dishwasher and leaking out.

Haier Dishwasher Error Codes Explained ' Exclusive Repairs

https://exclusiverepairs.co.uk > Blog
Dec 8, 2021 - The water inlet solenoid could also be defective. E6: All four lights flashing. Haier dishwasher E6 error code indicates that the flood ...

Feature : Error Code-control panel display "FA"

• Answer : Reason:Water level sensor error.
  Solution:Please unplug the machine and close the water tap, then call for service
  

Hi from retired Englishman in SW France,
The only reference to 'E08' I have is that there is a problem 'water level exceeds protection value'. Water level detection may not be operating correctly and requires a service engineer's attention I suggest ;-0(
If this has assisted and/or clarified the situation for you please consider a 4 thumbs up on our rating.
Thanks and good luck!
John C

OE is drain error, which means that the machine has detected that the water level is not lowering quickly enough...Probable cause is a blocked pump filter...Check via small door at floor level..Unscrew pump cover and clear filter....Remember that all water will drain from this point, so drain machine first...Leaning the machine back can help...Good luck....Nomess

It appears your pressure switch has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Err1 : Door not properly shut
Err2 : Drainage error (clean filter check hose
Err3 : temperature sensor short circuit
Err4 : Heater error
Err5 : water fails to meet specified level within 8 mins check tap, water pressure
Err6 : motor error
Err7 : motor error
Err8 : water exceeds protective level check circuit
End : end of wash cycle
Unb : after the last rinsing cycle finishes spinning fails completelt due to unbalance of the laundry

only reason I know is i looked through the manual after getting it myself could be something to do with running a bath while washer on or something perhaps not enough water getting in if powder channel blocked

The error code 7 is in fact a motor error.
The motor that drives the spin cycle has become faulty. The only solution now is to get an engineer in to fix it or get it sent away to get repaired.

Hi Mate;

Just had the exact same problem with the spin cylec and now its stopped completely, I was getting ERR 7 on the display, its telling you that there is something wrong with the motor.checked the motor and found that one of the Carbon Brushes was sticking/Stuck, Just 2 phillips head screws and the carbon brush is out, mine had a bit of melted plastic/casing snagging the Carbon brush, i just jusd a bit of fine sand paper to clean the Brush, put it all back together and lo and behold everyting works.
Hope this helps

Listed below are all the error codes:

Display messages:
Err1: Error message. Door is not properly shut 20s after program is started.
Correction: Shut the door properly.
Err2: Error message. Drainage error, water not emptied within 4 min.
Correction: Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel.
Err3: Error message. Temperature sensor is not properly connected or damaged (display at the end of a program).
Correction: Contact the maintenance personnel.
Err4: Error message. The heater may be broken or the desired temperature is not met within the specified time due to an overloaded laundry (display at the end of a program).
Correction: Reduce the load and restart, or contact the maintenance personnel.
Err5: Error message. The required water level is not reached within 10 min, or the water level exceeds the protection value.
Correction: Check to see if the tap is turned on and the water pressure is correct. If error still exists, contact the maintenance personnel.
Err6: Error message. Motor speed error. It may be not properly connected or damaged.
Correction: Contact the maintenance personnel.
Err7: Error message. Motor overheat protection or is damaged.
Correction: Contact the maintenance personnel.
Err8: Error message. Water level exceeds protection value.
Correction: Contact the maintenance personnel.

Regards

Bull

bosch exxel 1200 washng machine
has error message 04 and wont drain or spin

what does this mean?

can you help?
have lost instruction book