Hello, TAX-AMT is not printingon receipt after changing tax rate.

Hello,

Per the instructions on the Casio4Business Support website, you can do the following:

PCR 308, 350, 355, 408, 450
TO PROGRAM STATUS OF DEPARTMENT KEYS:

1. TURN KEY TO Z MODE
2. PRESS SUBTOTAL
3. PRESS 02 FOR TAX TABLE 1, 04 FOR TAX TABLE 2, 06 FOR BOTH TAX TABLES, AND 00 FOR NO TAX
4. PRESS DEPARTMENT KEY
5. REPEAT STEPS 3 & 4 FOR MULTIPLE DEPTS.
6. PRESS SUBTOTAL

You can access additional information at the main support site: http://www.casio4business.com/sa/support/taxtable_programming.html

Regards!

That is the correct program it seems your program is corrupt, just wipe out everything and start afresh

Casio TE2200: Key To PGM, Press 3 then Subtotal, 0125 Subtotal ( this sets tax table 1, 0225 will set table 2 etc), 6.725 CA/Amt Tend (insert your rate here), 0 CA/Amt Tend, 5002 CA/Amt Tend (this sets to Fraction Round Off and Add On Tax), Subtotal

Hi. You are working in the wrong area. You need to tell each department not to add TAX2. Go to the department programming, and there should be a setting that says use tax1, use tax 2 etc. Turn off tax2 for any depts that you don't want it added and it will no longer print or calculate tax 2 for that department.

--------------------------------------------------------------------------
For anyone looking for a Casio PCR-T2000 manual, see here:
http://the-checkout-tech.com/manuals/cashregisters/Casio2.php

To change the tax rate on your cash register, do the following:

• Turn key to PGM
• Press 3
• Press SUBTOTAL key
• Enter new tax rate ex: 7% is 7, 7.5% is 7.5
• Press CA/AMT TEND key
• Press SUBTOTAL key
• Return key to normal position

If this procedure doesn't work or you need to program more than one table, kindly post back. Best of luck.
Greg

You're right, the manual is terrible but I think I got it worked out...
Turn to PGM mode.

• Press 3 then subtotal button.
• Press subtotal button again.
• Then endter tax rate (if even enter two digits 05 for 5%, if more enter 4 digits like 5.75 *5+.+7+5 for 5.75%) and press ca/amt tend button
• Press 0 and press ca/amt tend button
• Press 0125 and press ca/amt tend button *this is for rounding/tax table code not positive on this one but looks like the right entry for "add on" tax
• Press sub total button

This should change your tax

1) switch to PGM mode
2) press 3 then sub total key
3) press 0125 for tax table 1 or 0225 for tax table 2 followed by the sub total key
4) enter tax rate percentage using the decimal point and then press CA/Amt Tend
5) press 5002 and then CA/Amt Tend (to round off results)
6) press sub total key

Absent any specific model information, I suggest you refer to the manual to see if there is a "calculate but don't print option". I doubt it seriously however, since the receipt would make no sense to the customer. It may be possible to trick the register by telling it to print those lines in a color that is not available on the print ribbon, but still the customer would be confused if they tried to manually total the bill..

On your Sharp press
CA
C.CE
C.CE
RATE SET(+TAX Key)
175(No decimals for they are not taken into consideration)
RATE SET(+TAX Key)

To check if all went well press
CA
C.CE
C.CE
RATE RECALL(-TAX Key)
It should read your tax rate.

I'm in Australia and only going on the program manual for your area, it states that canadian tax is tax on tax? if this is true then you probably entered a code for add on or add in tax and thereby changed it all.

you need the following

tax table address
1 125
2 225
3 325
4 425

rounding off codes
rounding off to 2 decimal places is 50
rounding up to 2 decimal places is 90
cut off to 2 decimal places is 00

tax system code
tax table with out tax rate 01
tax table with tax rate and add on rate 02
add in tax rate 03
Canadian tax-on-tax rate 04

starting point
to get the starting point you multiply by 100 and subtract 1
eg 50 cents = 0.50 X 100 - 1 = 50 - 1 = 49
eg $4 = 4.00 x 100 -1 = 399

to program the tables go through these steps

go to program 3
tax table address eg 125
subtotal
tax rate
ca/amt tend
starting point eg 0.50 = 49
ca/amt tend
rounding eg 50
tax system eg 04
ca/amt tend
ca/amt tend

here you have 2 choices,

press ca/amt tend to go to the next tax table ie 225 and start over by entering the tax rate and go through the procedure again

or

press subtotal to finalise the tax table you are on

Hope this helps,

Adam